02 S-10 V6 vortec turns over but will not start?
You need fuel, spark and compression. You are missing one of those, probably fuel (bad fuel pump).
Start looking at fire and gas. Trace these two that are the main problems. Read More
On the Vortec the computer does it all. Read More
1994 Chevy s10 with a 4.3 Vortec will just slow down while driving Sometimes if you stay on the pedal it will regain power And sometimes you have to pull over But you can start it back up?
bad fuel injector spider Read More
fuel injectors could be clogged Read More
A 1996 Chevrolet S10 with a 4.3 liter vortec holds approximately 4.5 quarts of oil. The recommended oil type of 5 W 30. Read More
A 95 S10 4.3 Vortec does not need a valve adjustment. Instead, a hydraulic lifter is used. To repair a bad lifter, add half a can of seafoam motor to tune the oil. Read More
for this I would loosen the exhaust in front of the converter see if it will run . This was the problem with my 4 cyl s10. The convereter was clogged Read More
click it over to the on spot but don't let it turn over (your letting the fuel pump fill that filter up) do it couple times then turn it over. and see if you set off the security light (it will flash if you did) Read More
i belive its 160 or 180 if its a vortec Read More
No, different bolt pattern. Read More
Why 94 4.3 vortec s10 blazer run it couple of hours and starts running ruff and stalling and not starting?
It maybe the Thermostat if it bad the 4.3 will quit and not start untile it cools down Read More
A 1995 S10 with the 4.3 L TBI requires 41 to 47 psi fuel pressure. Read More
Left side Read More
It is in the throttle body. Read More
What else can you check on your Blazer S10 Oil sensor is new Still hard to start Fuel pump Pressure sensor?
limited info, but id say its a crank sensor. turns over slow and choppy this could be your problem. turns over normal could be lack of spark or fuel. by turning over, i mean motor cranking but not starting. without more info its anyones guess. Read More
You need three things for the engine to run, compression, fuel and spark. You say you have fuel now check for spark. Read More
The engine will physically fit, however the wiring and electronics will not hook up, they are quite different, as is the fuel system. Read More
1996-98 blazer/s10 4.3l vortec Read More
2003 4.3's do not have an egr valve. Read More
With the intake runners to each cylinder. Read More
1995 blazer s10 v6 vortec hard to start in morning will run all day once started next morning same wont start changed tpv same?
Try replacing the coolant temp sensor, the one next to the thermostat housing. Read More
Check your starter. Read More
Probably the fuel pump. Read More
Your Chevy s10 wont start it turns over but doesn't fire you just a snow storm and it is all gone now what is wrong?
Check the Chevy S10s crankshaft position sensor. The sensor is located low on the engine, and the snow could have gotten the connection damp. The engine will not start when the sensor does not operate. Read More
1-6-5-4-3-2 Read More
1-6-5-4-3-2-1 Read More
its 1-6-5-4-3-2- Read More
inside left side frame rail under truck Read More
123456 with the even # cylinders on passenger side odd # on drivers Read More
The Standard Engine in the S series ZR 2 package is the 4.3litre Vortec 6Cyl Read More
yes it will Read More
depending on the year ,, I have a S10 with a vortec 4.3 V6 in mine its a 1998 ,, and it has the V6 Read More
Where can you find a schematic for the ignition control module of a 43 vortec engine in a 1994 Chevy Blazer S10?
Owners manual, positive. Read More
If it is a Vortec it will be inside the tube running from the intake to the air filter it is a rubber hose with this stuck in it! Read More
its in the air intake TUBE from the air filter intake air temperature IAT Read More
The one the ecm reads is located right next to the thermostat housing. Read More
just do what i did and take out the tumblers that the key slides over. Read More
My 99 Chevy s10 pick up died while i was driving I put more gas in it my battery works it turns over but just won't start What do I do?
Could be many things but the first one that comes to my mind is a fuel pump gone bad, not uncommon for GM. Read More
No. It would cause the check engine light to illuminate and fail an emissions test but it would start and run. Read More
It doesn't have one. Read More
it should but being that they are two years apart they might not yes they will 100% they are the same if they are 4.3, fyi the s10 sonoma only came with a 4.3 vortec v6 or a verry under powerd 2.2 4cyl Read More
make sure the spark plug wires are firing Read More
depends upon the truck, diffrent ratio's were used Read More
I have the same problem I changed the fuel pump and the ignition coil also changed the igition module,still the same problem engine turns over but wont fire,still no spark and no fuel getting through,was wondering if theres a sensor that turns everything off?? 1991 s10 owner email firstname.lastname@example.org Read More
Will the engine and transmission from a 1994 GMC Jimmy S10 SLE 4POINT3 liter vortec motor fit into a 1999 GMC Jimmy SLT?
the simple answer is YES. though, a 94 would be either a t.b.i. system or early vortec. if it is a vortec, the swap shouldn't require a p.c.m. reflash- however if your 94 is a t.b.i. you will need to change the intake and fuel delivery systems to handle the 60 p.s.i. operating pressure for the vortec engine. Read More
If it's a V6 it is a 4.3 litre vortec engine. If it is a four cylinder engine it is a 2.2 litre engine. Read More
= Editing WikiAnswer to "http://wiki.answers.com/Q/Why_would_there_be_a_substantial_amount_of_gas_in_your_oil_1992_chev_s10_blaszer_6cyl_vortec_4.3" = answer Read More