0
1983 GMC Vandura 2500 8 cylinder with a Quadrajet 4 barrel carb and failed emissions What do you need to do to adjust the carburetor?
If it a Rochester carberator, there is no mixture adjustment. That is an internal setting done when the carburetor was put together or at the time of rebuilding. The only adjustments you can make is to the idle and choke
I have a 93' 2500 vandura and It failed smog and I advanced the Timing a tiny bit and it passed....yaaaaay
What else can I help you with?
How do you replace a carburetor on a 1977 GMC Vandura 2500 Van with a 350 V8 engine?
To replace the carburetor on a 1977 GMC Vandura 2500 with a 350 V8 engine, start by disconnecting the battery and removing any air cleaner or intake components obstructing access to the carburetor. Next, disconnect the fuel line, throttle linkage, and any vacuum hoses attached to the carburetor. Remove the mounting bolts and lift the old carburetor off. Install the new carburetor by reversing the steps, ensuring all connections are secure and properly tightened before reconnecting the battery and starting the engine.
Where is idle srew location on 1995 gmc vandura 3500?
The idle screw on a 1995 GMC Vandura 3500 is typically located on the throttle body of the engine's carburetor or fuel injection system, depending on the specific engine configuration. For models with a carburetor, the idle screw is often found on the side or top of the carburetor, while for fuel-injected models, it may be integrated into the throttle body assembly. It's important to consult the vehicle's service manual for precise location and adjustment procedures.
How do you remove ignition cylinder 88 GMC vandura 2500?
To remove the ignition cylinder from an '88 GMC Vandura 2500, first disconnect the battery to prevent any electrical issues. Then, remove the steering column cover by unscrewing it, and locate the ignition switch. Insert the ignition key and turn it to the "Run" position; there should be a small pin or release tab on the ignition cylinder that you can press to release the cylinder. Finally, pull the ignition cylinder out while ensuring the key is in the correct position.
Where does the hose and tube connect from the PCV valve on a 1991 GMC Vandura 6-cylinder?
connects to throttle body(port C )
How do you replace the ignition switch key cylinder on the steering column on a 95 gmc vandura?
To replace the ignition switch key cylinder on a 1995 GMC Vandura, first disconnect the negative battery cable to ensure safety. Remove the steering column cover by unscrewing the screws that hold it in place. Then, insert the key and turn it to the "Run" position, press the release pin on the cylinder, and pull the cylinder out. Finally, insert the new key cylinder, ensure it locks in place, and reassemble the steering column cover.
How do you find out if your 1992 GMC 2500 Vandura van is EFI or carburetor?
take doghouse off, remove air-cleaner lid and look down into carburetori if you see a pair of injectors with electric wires going to them, its EFI
1986 gmc vandura 2500 8 cylinder firing order?
The firing order for a 1986 GMC Vandura 2500 with an 8-cylinder engine is typically 1-8-4-3-6-5-7-2. This order is critical for proper engine operation and should be followed when installing spark plug wires. It's advisable to double-check the specific engine configuration, as variations may exist depending on the engine type.
How do you adjust the choke on your 1985 vandura g2500?
To adjust the choke on your 1985 Vandura G2500, first locate the choke mechanism, which is typically found on the carburetor. You can adjust the choke by loosening the screws that hold it in place and turning the adjustment screw or rod until the choke plate opens fully when the engine is warm. Ensure the choke is closed when the engine is cold for proper starting. After adjustments, test the vehicle to confirm proper operation.
Where would You locate the ECM on a GMC Vandura 2500?
The ECM on the Vandura 2500 is under the Driver's seat.
Where is the proportionate value on the gmc vandura 1990?
mine is located straight down from the brake booster.....follow the brake lines coming off the master cylinder....should lead you right to the valve you are looking for
305 8cyl gmc vandura 2500 picture of the 2 transmission tubes that go from the engine to the transmission?
I'm unable to provide pictures directly, but in a 305 8-cylinder GMC Vandura 2500, the two transmission tubes you're referring to are likely the cooler lines that connect the transmission to the engine's radiator or external cooler. These tubes are typically metal or rubber and run along the side of the transmission. For a visual reference, you might check repair manuals or online forums dedicated to GMC Vandura vehicles.
What size motor doe a 1993 GMC Vandura 2500 have?
My 93' vandura has a 5.7 liter 350cubic inch engine.
