answersLogoWhite

0

Bleeder port may be blocked. Try breaking the brake line loose and see if you get fluid that way. Good luck!

User Avatar

Wiki User

17y ago

What else can I help you with?

Related Questions

How do you bleed the front brakes on a Honda crf450?

First make sure the fluid is full. Check that the bleeder can be opened. With the bleeder tight, have someone depress the brake and hold it in, you open the bleeder to let the air and fluid out. Close the bleeder and have the person release the brake. Check to make sure brake fluid is topped up, and repeat till all the air is out. Might help to attach a small hose at the end of the bleeder so that the brake fluid drains into a cup.


Can you unscrew the bleeder screw and pumped the brakes to empty out the brake fluid?

Yes, that is what the bleeder screw is for


Why doesnt brake fluid come out of the bleeder?

it wont just come out. you need to pump the brake pedal.


Where are a 1994 Pontiac Sunbird brake bleeder screws?

One at each Wheel just below where the Brake fluid line attaches. One or two at the Brake fluid reservoir.


Where is the brake fluid bleeder on a ram 1500 quad cab?

there is one at every wheel


Why no fluid comes out of bleeder?

the valve is probably corroded or there is sediment in the line and settled inside the bleeder. Remove the bleeder all the way and see if you get any fluid. be ready to re install the bleeder as you get fluid flowing. If you do not pump the brake pedal with the bleeder out you should be able to replace the valve with a new one quickly then bleed the brakes so get the air out.


How do you change the hydraulic fluid in a 1993 Saturn?

Hydraulic fluid could be used in two locations on your 1993 saturn. your brake system is of course Hydraulic, in this case, the easiest way to change the fluid is to obtain a vacuum brake bleeder kit from your local parts store. you will need to loosen each bleeder screw on all 4 wheels and attach the vacuum bleeder. keep an eye on the fluid level in the master cylinder so it doesnt get too low. 1 large bottle of brake fluid is enough to do an entire vehicle. If you are talking about the clutch fluid, which is also hydraulic, there is no method of changing the fluid. the unit is sealed and offers no bleeder.


How do I change brake fluid in a dirt bike?

have good supply of new correct brake fluid on hand easiest way to change fluid it to open bleeder valve on brake. fluid will run out die to gravity keep reservoir topped up till new fluid runs out of bleeder, tighten bleeder, make sure reservoir is at correct level, replace cap. do this to both wheels , one at a time . The answer above is a brief summary of how to do this but for a thorough explanation see the link below


How do you bleed brakes on a Peugeot 106?

To bleed the brakes on a Peugeot 106, start by ensuring that the brake fluid reservoir is filled to the appropriate level. Then, use a brake bleeder kit or a clear tube attached to the bleeder valve on the brake caliper. Have an assistant pump the brake pedal several times and hold it down while you open the bleeder valve to release air and old fluid, then close the valve before they release the pedal. Repeat this process until no air bubbles are visible in the fluid, and ensure to check and refill the brake fluid as necessary throughout the process.


How do you bleed ABS brakes on a 2012 Harley Davidson Road King?

To bleed the ABS brakes on a 2012 Harley Davidson Road King, start by removing the brake fluid reservoir cap and checking the fluid level. Use a brake bleeder kit or a clear tube attached to the bleeder valve on the brake caliper; open the valve and pump the brake lever to push old fluid out. Keep the reservoir topped up to prevent air from entering the system. After the fluid runs clear, tighten the bleeder valve, replace the reservoir cap, and check for proper brake function.


How do you get brake pressure on a 1995 gmc Yukon with abs after replacing abroken brake line and caliper?

Replace brake fluid in master cylinder keep eye on this fluid level. Open up the bleeder screw on Caliper and let gravity work the fluid out the bleeder screw until steady flow. This could take 15-20 min. Hopefully you added some brake fluid to the new caliper before installing. Once there is a steady flow tighten bleeder screw. You should be good to go !!!!! Another way is have some one pump the brake pedal until pressure is found and pedal is hard. Keep foot on floor and have someone open bleeder screw on caliper until pedal goes to floor. Keep pedal on floor and tighten bleeder screw. Again keep eye on brake fluid level and add accordingly. repeat this procedure until pedal pressure is good on first pump.....make sure to tighhten bleeder screw and keep eye on brake fluid level


1999 hino fe how to bleed hydraulic clutch?

gravity bleed the slave cylinder. then use a brake bleeder pump to pump fluid into the slave cylinder's bleeder valve. you will have to use a tool or turkey baster to remove the excess fluid from the reservoir and you pump the bleeder to prevent it from over flowing. do not reuse this fluid.