0
A container that is filled with object typical of a particular time and place?
Wiki User
∙ 14y ago
That is known as a time capsule.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Why do some objects float when placed in a container filled with a liquid while other sink?
It all depends on the density of the object. If an object was less dense than water, then it will float. If an object is more dense than water, then it will sink.
How can a object can stay in the air?
An object stays in the air when the density of the object is at equilibrium with that of the air. A good example of this would be a light-weight, hollow container filled with 50% helium, and 50% oxygen. This would stay perfectly stationary, so long as there was enough helium to counteract the container's weight, in mid-air. However, if the helium level is greater than the air within the object, it will continue to float upward until the density of the object is equal to that of the atmosphere around it.
Why do some object float when placed in a container filled with a liquid while other sink?
isipadu objek lebih tinggi berbanding air manakala isipadu sink lebih tinggi berbanding air
What is an object for holding things called?
it is called a container
State Archimedes' principle and give an example of how you could determine a buoyant force?
Archimedes stated that any object set in water will experience a force of buoyancy equal to the weight of the water displaced.To determine the buoyancy force of an object, follow the procedure below. You will need:Two containersAn accurate scale1. Find a container as least as wide and as deep as the object in question, and then find a second container that is wide and deep enough to catch spilled water from the first container. For example, use a measuring cup as the small container, and a cake pan for the larger container.2. Weigh the larger container. Write down this measurement - you will need it in step 8.3. Rest the smaller container in the middle of the larger container.4. Fill the smaller container completely and exactly full with water, such that the smaller container cannot hold any more water without spilling over. Be certain not to spill any water into the larger container during this step.5. Gently place the object in question in the smaller container - do not drop it into the water. Allow it to immerse into the water gently so that it does not splash. As you place the object in the smaller container, water will spill over the top of the container, and will be captured by the larger container.6. After the object in question comes to rest in or on top of the water, remove the object, again being careful not to spill or splash any water over the edge of the smaller container while removing the object.7. Remove the smaller container from the larger container.8. Now weigh the larger container with the water in it, and subtract the weight you measured in step 2 from this weight. The difference in weight is the weight of the water alone..The buoyancy force is the weight of the water you calculated in step 8.
How is an object put into earth?
First a hole must be drilled or dug, then the object is dropped therein. Alternatively, the object may be placed in a suitable container such as a box or a bucket, and the container then filled with loose soil.
What is the process of applying a Group Policy Object to a particular container such as a site domain or an organizational unit?
Linking
What method do you use to find the volume in a given object?
Assuming you can't work it out mathematically, fully submerge the object in a container filled to the top with water, then measure the volume of the water displaced.
Why do some objects float when placed in a container filled with a liquid while other sink?
It all depends on the density of the object. If an object was less dense than water, then it will float. If an object is more dense than water, then it will sink.
The unit of measure for volume of an irregular shaped object?
1. fill the container with water (make sure you write down what you filled it to) 2. Place object into the container 3. Calulate how much the water rose 4. Find the difference of the two numbers (that will be you volume of the irregular shaped object) 5. All finished!!!
How can you find your volume?
An easy and low tech way to find the volume of an object is to measure the volume of water it displaces. Fill a container that has lines for measuring volume on it with enough water to fully submerge the object whose volume you will measure, but don't fill it all the way to the top. Write down the amount of water you start with, let's say 1 liter. Now put the object you want to measure into the water carefully so that you don't splash any water out and make sure that it is fully submerged. Now write down the new volume of water in the container, let's say it now reads 2.5 liters. Subtract the original volume from the new volume to find the volume of your object: 2.5L - 1L = 1.5 liters. Another way to find the volume of an object fill a container with water to the very top of the container. Place that container of water into an empty larger container. Put the object that you want to measure into the container of water slowly so that you don't spill any more water than the object pushes out on its own. When the object is fully submerged, it should have pushed out some water into the larger container. To ensure accuracy, the level of water in the water filled container that now also contains the object to be measured should still be at the very top of the container. Carefully remove the water/object filled container from the larger container so as to not spill any more water. Carefully pour the overflowed water into a smaller measuring vessel to find the volume of your object.
What is a container object in active directory?
A container object is one that can other objects housed within it. These can be additional container objects or leaf objects.
What is displacement method?
The Liquid Displacement Method involves putting an object into a container filled with water. A measurement is then taken of how much volume of water has been displaced. This measurement can then be used to calculate the volume of the object displacing the water.
What displacement method?
The Liquid Displacement Method involves putting an object into a container filled with water. A measurement is then taken of how much volume of water has been displaced. This measurement can then be used to calculate the volume of the object displacing the water.
How do you fine the volume of a irregular object?
Put the object in a measuring container; pour in water to cover the object and measure the volume in the container; take the object out of container and measure the volume remaining. The difference is the volume of the object. If the object floats push it down until covered with water.
What is the volume of the stone?
The volume of a stone or any irregular solid non-porous object can be determined by placing the object slowly into a container filled with water up to the very top. The water that runs over the edge of the container must be collected and measured in another container, such as a cylinder type or rectangular/square shape from which a square area can be calculated to determine the displaced volume of water.
How do you measure the volume of an irregularly shaped object?
He saw that when he got in the bathtub the water moved out of the way to make room for his body. So if he put an object in a container filled with water that would answer his kings question.
