Starters and Ignition Systems
Mercedes-Benz 190-Series
New Electrical Work
Modification of Old Electrical Work

A wire diagram for a Mercedes 190 Ignition switch. A locksmith made a mess of removing the ignition Now you have to rewire it and am not sure which coloured wire connects to what terminal?

91011

Top Answer
User Avatar
Wiki User
Answered
2007-11-13 09:53:26
2007-11-13 09:53:26

RE Wiring for ignition switch the below is for 190 merc (w201 model) hope this is of use to you CIRCUIT 30 = RED 2 CONNECTIONS CIRCUIT 50 = PURPLE CUICUIT 15 = RED/BLACK CIRCUIT 15R = RED/GREEN CIRCUIT P30 = GREEN/WHITE (SMALL WIRE) CIRCUIT 15X = RED/YELLOW CITCUIT 15T = BLACK/BLUE

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


Ouch! this could be a problem. I would start by looking for a Bentleys guide. You may need to contact Mercedes directly or a repair shop for a wiring diagram.

Minus - connects to the distributor and Positive + connects to the ignition.

When turned to the "Off" position, it connects the ignition to the frame ground to turn off the ignition and therefore the spark (fire.)

Looking at the plug from the blade side directly on you should see a larger blade (silver) on the right, smaller (brass) blade on the left and a U shaped ground blade on the bottom. The white wire connects under the right (silver) coloured screw, the black wire connects under the left (brass) coloured screw and the green wire under the green ground screw. If it is only two wire lamp cord the wire with the raised rib on it is the identified neutral wire and it connects to the silver screw. The other connects to the brass coloured screw.

There are two visual differences between the "hot" and neutral side of a duplex receptacle. Looking at the face of the receptacle the blade sizes are different. The smaller blade is the "hot" side where as the larger blade size is the neutral.On the reverse termination points, the "hot" wire connects to the brass coloured screw and the neural wire connects to the silver coloured screw.The U shaped opening is for the ground blade and the reverse side, the green coloured screw is where the ground wire of the circuit connects.

In normal home wiring the black and white supply the circuit voltage. The green conductor connects to the green screw. The black conductor connects to the brass coloured screw and the white conductor connects to the silver coloured screw. There are additional terminals on the receptacle that connect to the down stream side of the circuit. By making these connections on the GFI receptacle all downstream normal duplex receptacles are also protected.

In order to obtain the radio code for a Mercedes ML320, your VIN number must be known. Each vehicle has a different VIN number that connects with the radio code.

Disconnect one cable of your battery and turn the car key to ignition position two times, connects your battery and turn the car key to ignition.

There is a lock ring on the inside of the dash where the switch connects. You need to remove this lock ring to remove the switch from the dash.

There are three terminals on a coil: positive, negative and "center." The center terminal connects to the center terminal on the distributor cap. Negative always connects to the condenser in the distributor. If you have a tachometer, it connects to the negative. Positive connects to three places: the ignition switch wire, the backup lights, and the choke heater on the carb or carbs if your car is so equipped. Quick troubleshooting technique: if your car dies when you put it in reverse, unplug the wire to the backup lights and see if it does it again. If it does, you have a short in the backup light circuit.

your coil's got a posative and a negative... Positive is Ignition hot and the negative connects to the distributor

There is an electrical connector located under sear that connects to seat belt buckle, just disconnect it.

On the driver's side of the engine just below the electronic ignition module. The thermostat housing connects to the top radiator hose.

check the wire harness that connects to the engine block, on the back

I have a M-B 300TE 6 Cyl gas. The thermostat is on the upper radiator hose cap that connects to the engine. Be sure engine is cold.

In North America the connections for a 15 amp cap (plug) goes as follows. Looking at the plug from the blade side directly on you should see a larger blade (silver) on the right, smaller (brass) blade on the left and a U shaped ground blade on the bottom. The white wire connects under the right (silver) coloured screw, the black wire connects under the left (brass) coloured screw and the green wire under the green ground screw.

The points are in parallel with the condenser. Both are connected to ground on one side (screwed to something metal). The other side connects to the coil.

Answer for USA, Canada and countries running a 60 Hz power supply service. Looking at the duplex receptacle from the front side directly on, you should see a larger blade hole (silver) on the left, smaller (brass) blade hole on the right and a U shaped ground blade on the bottom. The white wire connects under the left (silver) coloured screw, the black wire connects under the right (brass) coloured screw and the green or bare wire under the green ground screw.

More than likely the wire that runs from the ignition switch to the kill switch is disconnected, loose, or broken. The wire starts at the OFF position of the ignition switch and connects to another wire that shuts off the engine.

The small wire connects to the "S" terminal. The "R" terminal is not used if you have electronic ignition.

Look behind the red colored dipstick. You will see 2 ignition coils side by side (the spark plug wires connect to them) these are mounted on top of the ignition module. Each coil connects 2 spark plug wires. The coils have 2 bolts that hold them to the block. Disconnect the 2 plugs at the top of the ignition module. Remove the bolts holding the ignition coils to the ignition module and the whole assembly will come off.When replacing the coils, the spark plug order from left to right is 4-1-2-3 (the cylinder order on the block from left to right is 1-2-3-4).

A gateway, or router, connects different networks.A gateway, or router, connects different networks.A gateway, or router, connects different networks.A gateway, or router, connects different networks.

Wiring a duplex receptacleLooking at the duplex receptacle from the front side directly on, you should see a larger blade hole (silver) on the left, smaller (brass) blade hole on the right and a U shaped ground blade on the bottom. The white wire connects under the left (silver) coloured screw, the black wire connects under the right (brass) coloured screw and the green wire under the green ground screw. Wiring a group of receptacles together requires them to be paralleled together. White to whites, black to blacks and ground wire to ground wires.

Wiring a duplex receptacleLooking at the duplex receptacle from the front side directly on, you should see a larger blade hole (silver) on the left, smaller (brass) blade hole on the right and a U shaped ground blade on the bottom. The white wire connects under the left (silver) coloured screw, the black wire connects under the right (brass) coloured screw and the green wire under the green ground screw. Wiring a group of receptacles together requires them to be paralleled together. White to whites, black to blacks and ground wire to ground wires.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.