The 2003 Hyundai Tiburon has door handles that sometimes break or need replaced. They can be easily removed and replaced with a new part.
hyundai tiburon 2001 all vacum hoses OK new spark plugs i have spark engine will start but hard to start firing order OK but wont stay on what can it be is it intake sensor or not enough fuel pressure
i have the same problum with my tiburon! if you get the answare can u call me at 772 204 3186 that's my cell, i would really appretiate it!
The Hyundai Tiburon (a.k.a. Hyundai Coupé) is a compact coupe produced by Hyundai since 1996. The name itself means "shark" in Spanish. Tiburon is the name given to the current North American, Australian, New Zealand, South African, and Austrian production of the vehicle, though it is called the Hyundai Coupe in world markets. It has also been known by the moniker Turbulence and Tuscani in the South Korean market. The model has been released in two generations (RD and GK) over its lifespan and in that time these generations have been subject to periodic facelifts. These facelifts have attempted to keep the car up to date with various safety improvements and a mixture of changes to exterior and interior styling. The RD Tiburon was in production for 5 years from 1996 to 2001. The GK Tiburon has been produced since 2002 and is still in production in its latest guise. Enthusiasts sometimes refer to it using the nickname 'Tib' or 'Tibby' in the markets in which it is called the Tiburon. Hyundai officially announced that the 2008 model year will be the last for the Tiburon. While no replacement has been announced, Hyundai has officially stated that the 2010 Genesis coupe is not a Tiburon replacement
According to the 3 different Hyundai dealerships there is not a turn signal relay on a 2003 tiburon. But it is actually located inside the BCM, if you can trust your self with opening the bcm you can change it yourself. Also if you call the dealer they will tell you that the only solution is to replace the BCM but they are full of it, they say that because it a new unit cost $1100+!
The Hyundai Dealership may have to "flash" the new BCM. They generally charge one hour labor for this service.
To retract the rear caliper on a 2006 Hyundai Tiburon, you'll need a brake caliper tool or a C-clamp. First, remove the caliper from the bracket by unscrewing the bolts. Then, using the tool, rotate the caliper piston clockwise to retract it fully into the caliper housing. Once retracted, you can reinstall the caliper over the new brake pads.
To change the flasher relay on a 2003 Hyundai Tiburon, first, locate the relay, which is typically found in the fuse box under the dashboard on the driver's side. Remove the fuse box cover and identify the flasher relay, which may be labeled. Gently pull the old relay out and replace it with a new one, ensuring it is securely seated. Finally, test the turn signals to confirm that the new relay is functioning properly.
The Hyundai Dealership may have to "flash" the new BCM. They generally charge one hour labor for this service.
To replace the headlight bulb in a 2005 Hyundai Tiburon, first, open the hood and locate the back of the headlight assembly. Disconnect the power connector by twisting it counterclockwise, then remove the old bulb by pulling it straight out. Insert the new bulb without touching the glass, secure it in place, and reconnect the power connector. Finally, test the headlight to ensure it’s working properly.
Unbolt the engine lift it up and turn it to the side where u see the tranny, unbolt the transmission, unbolt the pressure plate from the flywheel, take the clutch out, when u put a new one in make sure to use a clutch allingment tool
To change the side mirror on a 2006 Hyundai Tiburon, first, remove the door panel by unscrewing the screws and carefully prying it off. Once the panel is removed, disconnect the wiring harness for the mirror if equipped with power adjustments. Then, unscrew the mirror from the door using a socket wrench, replace it with the new mirror, and secure it with screws. Finally, reconnect any wiring and reattach the door panel.