0
Calculate the resistance in a circuit in which a 9 volt batteriyproduces 3 ampheres?
Wiki User
∙ 15y ago
V=IR so, R=V/I or resistance = Voltage / Amps Therefore, the resistance (R) = 9 volts / 3 Amps answer: 3 Ohms
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How do you calculate the joint resistance in a series circuit with three resistances?
The resistance of a series circuit is simply the sum of the individual resistors.
What is common to both thevenin and norton theorem?
To solve any D.C. circuit by using Thevenin Theorem,First of all load resistance RL is disconnected from the circuit and open circuit voltage across the circuit is calculated (known as Thevenin equivalent voltage)Secondly, the battery is removed by leaving behind its internal resistance. Now we calculate equivqlent resistance of the circuit ( called Thevenin equivalent resistance).Now we connect Thevenin Voltage in series with Equivalent resistance of the circuit and now connect load resistance across this circuit to calculate current flowing through the load resistance.Whereas in the case of using Norton theorem, we again remove the load resistance if any, and then short circuit these open terminals and calculate short circuit current Isc.Second step is same as in Thevenin theorem i.e. remove all sources of emf by replacing their internal resistances and calculate equivqalent resistance of the circuit.Lastly, join short circuit current source in parallel with equivalent resistance of the circuit. Now, we can calculate votage across the resistance which was connected in parallel with Isc.So, by knowing the open circuit voltage, we can calculate current flowing the resistance and on the other hand , by knowing the short curcuit current , we can calculate voltage across the resistance.
How do you calculate the voltage in a circuit with a resistance of 20hms and a currents of 6?
Use Ohm's Law. In this case, multiply the resistance by the current.
How much resistance is required for a circuit with an applied voltage of 30 volts and a circuit current with 1.3 ampheres?
This sounds like highschool physics homework. The answer is simple ohms law and algebra. The short answer is Voltage = Current x Resistance. If you know two things you can find the third. To be honest, this is a simple question and your book or Wikipedia can tell you. Just solve for the unknown.
When more light bulbs are added in parallel to a circuit what happens to the total resistance of the circuit?
"http://www.tpub.com/neets/book1/chapter3/1-26.htm" This site explains how to calculate the resistance, but it decreases the resistance when you add more.
State 3 functions of wheatstone bridge?
Wheatstone bridge is used to calculate the resistance of unknown resistor in the circuit.
What would happen to circuit if there was no resistance?
a circuit with no resistance or zero resistance can be considered as open circuit in which the current is zero. without resistance the circuit just becomes open ()
How do you find resistance when you have current and resistance total?
If you are looking for the resistance of each resistor in either a series circuit or a parallel circuit you must measure the current I and the voltage V for each resistor. Then calculate its resistance using Ohms Law R = V / I where I = current (Amps), V = voltage (Volts) and R= resistance (Ohms).
Diode reverse breakdown14v current of 70mA and an un-stabilised supply voltage of 28v calculate resistance?
If a circuit element has a voltage of 14V and a current of 70mA, then the resistance of the circuit element is 200 ohms. This is ohm's law. The resistance or type of the power supply is meaningless.
How do you calculate thevenis resistance in thevenis ckt?
First,remove all current and voltage sources ie replace voltage source with a short and keep current source open.Now draw the equivalent resistance-only circuit and find the equivalent resistance as viewed from the terminals of the circuit.
Is the increase in voltage causes a greater electric resistance in a circuit?
No, the resistance in a circuit does not change when voltage changes. Resistance is an inherent property of the circuit.
How is the total resistance in a series circuit is determined?
The total resistance in a series circuit is determined by adding (summing) the individual resistances of each component in the circuit.
