NO! The National Electric Code requires a partitioned box when high and low voltages share the same box. Always avoid installing different voltages in the same box, it's a bad idea.
<<>>
A 277 volt switch has a different screw to box configuration that a 120 volt switch. This is also true for 347 volt switches. The switch is configured this way so that 120 volt switches can not be used on the wrong voltage inadvertently
According to the 2008 NEC 300.3 C 1 says yes as long as all the conductors in the wiring enclosure have at least an equal insulation rating as that of the maximum circuit voltage applied.
Yes, you can run different system voltages in the same conduit and boxes. The conductors must be rated for the highest voltage present and used on all circuits.
Yes, a 220 volt appliance can be installed in your home.
What gauge of wire is required to carry a certain amperage X number of feet? How do you break out a 120 volt circut from a 3 phase line? When installing a load center, how should the ground be installed? What locations require Ground Fault Interrupters to be installed? How should a 240 volt dryer plug be wired? What is the minimum size conduit that 3 0 gauge wires can be pulled in? Can 12 guage Romex be used to wire a water heater?
You may not be able to do that. The 12V system will have a larger cord and may not pass thru the exhisting conduit. Call an electricial who knows swimming pool electrical codes.
Answer for USA, Canada and countries running a 60 Hz supply service.240 volt two wire circuits loads do not need a neutral to operate. A three wire 240 volt circuit that needs a neutral, will have a neutral the same size as the current carrying conductors. In this case a #10.
Absolutely not!! 277 volts is developed from a 480 volt power supply employing 1 conductor and a neutral. 240 volt power comprises two hot conductors and NO neutral.
Yes, 120 and 240 volts can be run in the same conduit.
Yes 480 volt electric wiring can be run in emt conduit.
That depends on the size of the conductor and the type, which is defined by its insulation. With many common large feeder conductors such as THHW, the largest conductor which you can run 8 of is # 2 gauge. Whereas common small branch circuit conductors such as # 12 THHN, you can run 138 ea. through a 2 " conduit. For the complete list, look at the chart titled "Maximum number of conductors in electrical metallic tubing" (EMT) in the National Electrical Code.
Yes
Yes, a 220 volt appliance can be installed in your home.
Conduit is just a medium to get the wires from one place to another. There is no voltage restrictions in low voltage wiring (750 volts or less). When it comes to conduit fill, electricians are governed by the electrical code conduit fill tables. The conduit is sized to accommodate the conductor size for a specific load.
On a 120/240 volt distribution the neutral is sized along with the supply conductors. The sizing is based on the amperage of the service distribution.
What gauge of wire is required to carry a certain amperage X number of feet? How do you break out a 120 volt circut from a 3 phase line? When installing a load center, how should the ground be installed? What locations require Ground Fault Interrupters to be installed? How should a 240 volt dryer plug be wired? What is the minimum size conduit that 3 0 gauge wires can be pulled in? Can 12 guage Romex be used to wire a water heater?
No, not unless you installed a 6 volt battery instead of a 12 volt battery.
There should be at least 2 meg-ohms between the current carrying conductors and between current carrying conductors and ground.
You may not be able to do that. The 12V system will have a larger cord and may not pass thru the exhisting conduit. Call an electricial who knows swimming pool electrical codes.
You tell yourself the 125 volt receptacle is a 120 volt receptacle. They're the same thing.