No, the source voltage can not change to a lower voltage without using equipment to do so.
Answer for USA, Canada and countries running a 60 Hz supply service.Breakers are rated in amperage and by the amount of poles that they have. Your classification of a 220 breaker is described in electrical terminology as a two pole breaker.Choosing the amperage of the two pole breaker depends upon the 220 volt load that it feeds.Two pole breakers for 220 volt loads.Single pole breakers for 120 volt loads.If the service is only 120 volt then every other bus bar in the panel will be energized. If the panel is a 120/240, then every bus bar in the panel will be energized.This is how and why a 240 volt load requires a two pole breaker.To the answer, yes you an use a two pole breaker in a 120 volt service but only one side of the breaker will have voltage on it depending on where it is situated in the panel board.
Yes, 220 volts is in the same voltage classification as 230 volts.
Grounding monitor
If you want mood lighting just connect it as is, the brightness of the bulbs will be half. If you want full brightness change the bulbs to 120 volt with bulbs of the same wattage as the 220 volt bulbs.
No, you will need a commercial mixer for that.
temporary it blows or KABOOOMM....
A three phase panel will not give you 110 and 220 volts. A three phase four wire panel will, but not at these voltages. The nearest voltages will be 120 and 208 volts. The 120 volt is the wye voltage of 208 volts. 208/1.73 = 120 volts. A single phase three wire panel will give you 110 and 220 volts.
Answer for USA, Canada and countries running a 60 Hz supply service.Breakers are rated in amperage and by the amount of poles that they have. Your classification of a 220 breaker is described in electrical terminology as a two pole breaker.Choosing the amperage of the two pole breaker depends upon the 220 volt load that it feeds.Two pole breakers for 220 volt loads.Single pole breakers for 120 volt loads.If the service is only 120 volt then every other bus bar in the panel will be energized. If the panel is a 120/240, then every bus bar in the panel will be energized.This is how and why a 240 volt load requires a two pole breaker.To the answer, yes you an use a two pole breaker in a 120 volt service but only one side of the breaker will have voltage on it depending on where it is situated in the panel board.
Yes. But not the other way. 120 volt one, cannot withstand 220volt.
Yes a 220 volt light bulb will run on a 120 volt circuit but at 1/4 of the wattage that the light bulb is rated at. A 100 watt light bulb on 220 would would be equal to a 25 watt light bult on 120 volt system.
no , it will burn out
Most residential service in USA has both. In the USA 110 to 120 volts is a given and it would be very unusual not to have 220 to 240 volts. It can be easily tested at main panel with a volt meter. Or as an alternative call your power company.
There is no remedy but to plug it into a 230 circut.
Yes, 220 volts is in the same voltage classification as 230 volts.
No. You need to rewire the circuit from the electric panel.
Generally, yes. Most US home services are 220 volt (240, 220 are `nominal' names) which are split into two 120 volt legs. You can find wiring information ont he internet, but generally, the 220 volt systems have a 120 volt leg, a common ground and then another 120 volt leg. Added together, they're 220 volt but by splitting them, you'll end up with two 120 volt legs. If you're not sure about how to wire them up, contact a qualified electrician to help you. House wiring can be very dangerous if you don't know what you're doing as well as lethal. When in doubt, don't.
you don't. you just take and use 120 volts from the 220. At least that's what I'd do.