0
No. Line voltage is 120v or some multiple there of. It is the potential that comes in from the grid and is found on the hot conductor in your house wiring. 24 volts is "low voltage" and tends to be used only for switching and lighting. Also, 24 volts is often DC (though not always) while line voltage is invariably AC
What else can I help you with?
Why electronic circuits work at 24volts?
A circuit is designed to work at a specific voltage and that voltage only.
How you calculate the line -line voltage?
Line-to-line voltage in a three-phase system is calculated using the formula ( V_{LL} = \sqrt{3} \times V_{LN} ), where ( V_{LN} ) is the line-to-neutral voltage. This relationship arises because the line-to-line voltage represents the voltage difference between two phases, while the line-to-neutral voltage is the voltage from a phase to the neutral point. If you have the line-to-line voltages directly measured, you can also use the voltage differences between any two phases to determine the line-to-line voltage.
What is 85 percent of 24volts?
20.4 volts.
What is edge speed in electronics?
A voltage is applied to a signal line. The voltage of the line changes gradually from 0 to +V. The "edge speed" is the rate of change of voltage of the line. A voltage is applied to a signal line. The voltage of the line changes gradually from 0 to +V. The "edge speed" is the rate of change of voltage of the line.
How do you convert 3 phase RMS line-line voltage to RMS line-neutral voltage on an unbalance system Basically how do you calculate using trig for all 3 phase?
The term, 'unbalanced system' refers to an unbalanced load. Under normal circumstances, an unbalanced load leads to unbalanced line currents. The line voltages are determined by the supply and remain symmetrical, even when the load is unbalanced. As your question refers to a 'line to neutral' voltage (i.e. a phase voltage), you must be referring to a star (wye) connected load, in which case the phase voltage (line to neutral voltage) is 0.577 (the reciprocal of the square-root of 3) times the line voltage (line to line voltage).
How do you convert 440 voltage line to voltage phase?
To convert a 440V line voltage to phase voltage in a three-phase system, you divide the line voltage by the square root of 3 (approximately 1.732). This means the phase voltage is calculated as ( V_{phase} = \frac{V_{line}}{\sqrt{3}} ). For 440V line voltage, the phase voltage would be approximately 254V.
Is 220V line voltage or phase voltage?
Phase, if you are referring to line, as power line from pole.
What will be the breakdown voltage of ciruit if 3 zener diode are connected in series having breakdown voltage of 8 volt each?
A: Any zener connected in series will have each voltage added to the load. Therefore each will add 8 volts to the sum of 24 volts. there will be available at each junction as 8v 16v and finally 24volts
What is the line voltage between two lines?
the voltage between 1 line & phase =120v The voltage between 2 line =240
Why is phase voltage not twice line voltage?
Line to line voltage is not the same as line to neutral voltage because line voltages are 120 degrees apart. They are related by: Line to neutral voltage * tan (120 degrees) = Line to neutral voltage * 1.73.Additional CommentFor delta-connected systems, the line voltage is the same as the phase voltage.For wye-connected systems, the line voltage is larger than the phase voltage by a factor of 1.732. The reason for this is as follows:Because any two phase voltages are displaced from each other by 120o, they must be added vectorially, not algebraically, to find the line voltage. As the above answer points out, this means that the relationship between the two is the square-root of 3, or 1.732.
What is a line to line voltage?
In a 3 phase system, the voltage measured between any two phase is called line to line voltage.And the voltage measured between line to neutral is called phase to neutral (line to neutral) voltage.AnswerThere is no such thing as a 'phase-to-phase' or a 'phase-to-neutral' voltage. The correct terms are 'line-to-line' and 'line-to-neutral'.The voltage between any two line conductors is called a line voltage.In a three-phase, three-wire, system, the line voltage is numerically equal to the phase voltage.In a three-phase, four-wire, system, the voltage between any line conductor and the neutral conductor is called a phase voltage. The line voltage is 1.732 times larger than the phase voltage.
Is transmission voltage a phase to phase voltage or a phase to ground voltage?
Phase to Phase voltageCorrection to the above answer:There is no such thing as a 'phase-to-phase' or 'phase-to-ground' voltage. The correct terms are 'line-to-line' (or 'line voltage') and 'line-to-ground' (or 'phase voltage'). Transmission-line voltages are line-to-line (or 'line') voltages.
