0
Not sure why you might want to, but yes, the vehicle will still run.
Wiki User
∙ 9y ago
Add your answer:
Earn +20 pts
How do you replace the egr valve on a 1992 Honda Accord EX?
1) Unplug the electrical connector for the EGR valve lift sensor. 2) Remove the two nuts that secure the EGR valve and detach the valve. 3) Clean the mating surfaces of the EGR valve and adapter. 4) Install the EGR valve using a new gasket. Tighten the nuts securely. 5) Plug in the electrical connector. These instructions come from the Haynes repair manual for Honda Accord 1990-1993 which also has good illustrations.
How do you replace the EGR valve on a 2001 Pontiac Montana van?
There is one bolt that holds the egr tube to it and two bolts that hold it to the intake manifold take them out, unplug the electrical connector and its off.
Is any programming or additional adjustments needed after a new egr valve is installed in a 2000 Toyota Camry 4 cylinder?
No but if there is still an EGR valve problem then its the EGR Valve switch located at the back of the motor. I replaced my EGR valve 2 times before I figured out it was the electrical switch, which had burnt up, for the egr valve. I havent had a problem with the EGR since then..
Where can you find the EGR position sensor on a 1993 Ford?
The EGR position sensor is located on top of the EGR valve. Has an electrical connector attached.
How do you install egr valve solenoid for 2001 Hyundai santa fe?
Unplug the vacuum line from the EGR valve then unbolt the 2 bolts ( i believe these are Number 11 metric ) that hold the EGR Valve. Make sure to remove gasket. replace in reverse, always replace the gasket. Plug Vacuum line back into the EGR Valve. This should take 10-15 minutes
How do you replace a EGR in a 1996 Saturn SL1?
The EGR valve is located on the drivers side of the head, just above the transmission bell housing. Remove the electrical and vacuum connections, then remove the two bolts that hold the EGR valve to the head. Use a NEW gasket when replacing the EGR valve.
How do you change the egr valve on a 96' dodge neon?
The EGR valve and electrical transducer should be replaced at the same time as they are matched. Remove EGR transducer from the air inlet duct. Disconnect vacuum supply tube from EGR transducer solenoid. Remove air inlet duct. Remove EGR tube to EGR valve screws. Remove EGR valve mounting screws. Remove EGR valve and transducer. Clean gasket surfaces. Discard old gaskets. If necessary, clean EGR passages. Loosely install EGR valve with new gaskets and finer tighten EGR tube fasteners. Tighten tube fasteners to 95 in lb, tighten EGR valve mounting screws to 200 in lb. Install air inlet duct. Connect vacuum supply tube to solenoid. Attach electrical connector to solenoid. Install EGR transducer onto air inlet duct.
How do you replace an EGR valve on a 2001 Ford Focus with DOHC engine?
Removal Remove the air cleaner outlet tube. Disconnect the mass air flow (MAF) sensor electrical connector. Disconnect the breather pipe. Remove the air cleaner. Fully loosen the exhaust gas recirculation (EGR) valve to exhaust manifold tube nut from the bottom of the EGR valve. Disconnect the vacuum line from the top of the EGR valve. Remove the EGR valve. Remove and discard the EGR valve gasket. Installation NOTE: Use a new EGR valve gasket when installing the EGR valve. To install, reverse the removal procedure.
Egr valve location on a 2001 Chevy 2500 hd 6.0?
If you look at the passenger front side of the valve cover were you put the oil in you will see a big round thing with an electrical connector pluged into it. That is the EGR valve.
Where is the egr valve located on an h22a4?
The EGR valve is located at the front of the h22a4 engine. The EGR valve is right beside of the front of the EGR valve.
Symptoms of bad egr valve is bad on 1995 aurora?
My Aurora had a slight hesitation or rpm surge at about 1500 rpm. disconnecting the electrical connector from the EGR valve and the problem went away.
How do you replace an egr valve in a 2002 Astro AWD?
1.Detach the cable from the negative terminal of the battery. 2.Remove the engine cover and the air cleaner and housing assembly. 3.Detach the the vaccum line from the egr valve vaccum tube. 4.Trace the temperature switch pigtail lead to the main engine wire harness and unplug the electrical connector, then remove the switch from the valve. 5.Remove egr mounting bolts (2). 6.Remove egr valve and gasket from the manifold. Clean mounting surface with wire wheel or wire brush. 7. Installation is reverse of removal.
