0
If this question is asking if, by using a GFCI, you can protect some equipment controlled by an existing switch, the answer is Yes. My first guess would be that you probably don't need to. A switch that is controlling lighting in an area with a GFCI, such as a bathroom, should - if it was installed correctly - already be controlling a proper lighting fixture. By this I mean if the fixture is above the shower it will be of a type that is safety-listed 'for use in wet locations'. That type of light fixture does not need to be protected by a GFCI since it is designed for use around water. How to feed a switch from a GFCI: Without GFCI protecting the switch: Connect a hot (usually black) wire from the "LINE" side of the GFCI (which will be marked) to one brass screw of the switch. (Assumption is single pole switch.) Connect another hot wire from the other brass screw of the switch to the light fixture or load's hot wire. Connect a neutral (white or gray) from the LINE side of the GFCI all the way to the load neutral without stopping anywhere. Connect all grounds. To GFCI protect the switch: The procedure is the same except you will use the hot and neutral from the "LOAD" side of the GFCI. This will cause the GFCI to interrupt power should a ground fault occur on the switched load. <><><>
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.
Before you do any work yourself,
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
What else can I help you with?
Why is my GFCI receptacle not working?
Your GFCI receptacle may not be working due to a tripped circuit, a faulty GFCI receptacle, or a wiring issue. It is important to troubleshoot and potentially replace the receptacle to ensure safety and functionality.
Can I install a GFCI receptacle from an existing receptacle in the basement?
Yes, there is no reason why this can not be done. In fact a benefit of this is that every receptacle downstream from this new receptacle will also be protected by the GFCI receptacle.
Can you install an electrical switch before a gfci?
Yes, an electrical switch can be installed before a GFCI outlet in a circuit. Just ensure that the wiring is done correctly, following all safety guidelines and local electrical codes. The GFCI outlet should be properly connected to the power source and the switch should be wired to control the flow of electricity to the outlet.
What might happen if the line and load connetions of a feedthrough gfci receptacle were reversed?
Most probably the receptacles downstream from the GFCI would not be protected by the GFCI receptacle.
Do you need a gfci outlet if you have a gfci breaker?
Not if the GFCI breaker is supplying the circuit you are wanting to put the GFCI receptacle into.
What is the weight of a GFCI receptacle?
8 ozs. and will vary by mfr. for an in-wall receptacle.
If I have 20 amp GFCI receptacle and would like to add another receptacle to the GFCI Does the new plug also need to be 20 amps?
Yes.
How far do you put a GFCI from water?
How far do u put a GFCI receptacle from water
Will another electrical outlet that is in line with a GFCI outlet cause it to kick off?
A down stream receptacle that is connected to the upstream GFCI will be protected. If the downstream receptacle senses a fault the upstream GFCI will trip.
Why won't the GFCI receptacle reset?
The GFCI receptacle may not reset due to a faulty connection, a tripped circuit, or a malfunctioning GFCI outlet. It is important to troubleshoot the issue to determine the exact cause and address it accordingly.
What does the term GFCI receptacle stands for?
The term GFCI stands for Ground Fault Circuit Interrupter.
What are the installation requirements for a 20 amp GFCI receptacle?
The installation requirements for a 20 amp GFCI receptacle include ensuring the power is turned off, connecting the wires correctly following the manufacturer's instructions, and securing the receptacle in place. It is important to test the GFCI after installation to ensure it is working properly.
