0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What does an fuse do in an circuit?
A fuse protects the (expensive) circuit for too high currents. When the current becomes too high the (cheap) fuse melts and the current is stopped, preferably before damage has been done to the circuit.
What happens when the voltage standing wave ratio is too high?
If the vswr (Voltage Standing Wave Ration) is high than call drop chance increase.
Explain why diodes melt?
Diodes, like many other electronic/electrical components, will melt if the temperature is high enough. This would occur if the power dissipation were too high because the current was too high.
What happens if transformer wattage is much less than load wattage?
If the load current is too high, the power lost in the transformer windings will be too high and it will overheat. If the voltage is excessive, the power lost in eddy currents in the magnetic core will be too high and it will overheat.
What is the function of a summation current transformer?
Current transformers are used to measure electric currents. When current in a circuit is too high to directly apply to measuring instruments, a current transformer produces a reduced current accurately proportional to the current in the circuit, which can be conveniently connected to measuring and recording instruments.
The electrical current breaks when?
the current becomes too high
How if the magnesuim is not polished would the reported mole ratio of oxygen to magnesium be too high too lowor unaffected?
If the magnesium is not polished, there may be impurities or oxides on the surface that could affect the reported mole ratio of oxygen to magnesium. This could result in a higher reported mole ratio due to the presence of excess oxygen-containing compounds on the surface, leading to an inaccurate measurement of the actual ratio of oxygen to magnesium.
The sample is not completely thermally decomposed in the procedure will the mole ratio of CaO To CO2 be too high or too low. explain?
The mole ratio of the sample will be too high. This is because the amount of CO2 will be lower than if the reaction went all the way and produced the proper amount of CO2.
What happens in a fuse when the current gets too high?
It melts (fuses).
Why are some channels blurry?
if you mean fuzzy as in not a very high resolution its because you have too high of a pixel ratio for cable (meaning if you have 1080p or anywhere near that ratio then it is too much for cable), i would advise upgrading to charter high definition though if you mean that its static i cannot explain that sorry.
What does an fuse do in an circuit?
A fuse protects the (expensive) circuit for too high currents. When the current becomes too high the (cheap) fuse melts and the current is stopped, preferably before damage has been done to the circuit.
What happens to a switch that automatically opens the current if it is too high?
Circuit Breaker.
What is damaged resistor?
A damaged resistor is one that it fried by current that is too high
How to make THE WORST bacon EVER?
cook it at too high a heat
Is quick ratio a better measure of the firms liquidity than current ratio?
Yes because a quick ratio doesn't include inventory which must be sold before it can be used to pay for the companies current obligations. Of course you have to collect the cash in A/R before it can be used to pay for current obligations too but AR should be able to be converted to Cash much quicker than Inventory. A Cash Ratios, which doesn't include AR or Inventory is an even better measure of a firms liquidity than both the quick and current ratio.
Why ohm's law is applicable for steady current?
It's an immutable law of physics! It applies to a.c. too but only if the circuit is purely resistive.AnswerOhm's Law is not a universal law, and only applies to a limited range of conductors or loads, called 'linear' or 'ohmic' conductors or loads. Basically, it only applies when the ratio of voltage to current is constant for variations in applied voltage. If this ratio changes for variations in voltage, then the conductor (e.g. tungsten) or load (e.g. diode) does NOT obey Ohm's Law and is termed 'non-linear' or 'non-ohmic'.The ratio of voltage to current is called 'resistance', and the ratio will ALWAYS tell you what the resistance happens to be for that particular ratio (if the ratio varies with voltage, then so too does the resistance), whether the conductor/device obeys Ohm's Law or not!So Ohm's Law really has nothing to do with a circuit having a 'steady current'; it's all to do with whether or not the ratio of the circuit's voltage to current is constant for variations in voltage. Nothing more!
What happens when the voltage standing wave ratio is too high?
If the vswr (Voltage Standing Wave Ration) is high than call drop chance increase.
