0
What else can I help you with?
What size breaker should be used with ceiling fans?
Use 15 amp breaker with 14 gage wire or 20 amp breaker with 12 gage wire. Either way will work just fine.
Will it hurt to use a 40 amp breaker on a water heater the wire I was sold will not fit into the 30 amp on a sq. D circuit breaker?
In the United States, if the wire is #8 copper or larger (smaller number) it will work fine on a 40 amp breaker. If the wire is #10 copper, there is something wrong with the breaker if it does not fit. Pull the breaker out of the panel and look into where the wire terminates to see why the #10 wire won't fit.
How do I wire an AC unit to a breaker box?
To wire an AC unit to a breaker box, you will need to connect the AC unit's wiring to a dedicated circuit breaker in the breaker box. Make sure to follow the manufacturer's instructions and local electrical codes to ensure proper installation and safety. It is recommended to hire a licensed electrician for this task if you are not experienced in electrical work.
Will a 14-2 gage wire work for a 240 volt 15 amp breaker?
No. You will need a 14/3 with Ground.
Compare conductivity of iron copper and aluminum in terms of electricity.?
When compared by volume, copper is best, then aluminum and finally iron. When compared by weight, aluminum is better than copper. You have to compare by volume because aluminum is so much lighter than copper, an aluminum wire that weighed the same as a copper wire would be much bigger and harder to work with.
What is an example of a conducter?
A wire carrying electricity to a load. The wire conducts the energy from a source to a device. That connection in a complete circuit does work.
How do you wire a ge double pole 50 amp circuit breaker with black white and ground?
Answers for USA, Canada and countries using similar 60Hz mains supply.By stating that it is a double pole breaker it is presumed that the load device needs 240 volts to operate. Connect the black wire to one pole of the breaker. Apply black electricians tape to the white wire to identify it as a current carrying conductor. This wire is then terminated into the second pole of the breaker. The ground wire is terminated on the terminal ground strip in the back of the breaker panel. On the load end also identify the white wire with black tape before connecting it to the load. What this signifies to any one with electrical knowledge is that the white wire is not a neutral but carries load current.If you do any such work yourself, always turn off the power at the breaker box/fuse panel BEFORE you attempt to do any work AND always use a meter or voltage indicatorto insure the circuit is, in fact, de-energized.IF YOU NOT ALREADY SURE YOU CAN DO SOME ELECTRICAL WORKSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
What is the color of the wire from the head lights to circut breaker?
how do i find a short in my head lights ,tail lights work but not my head lights
Would aluminum work with electrical wire?
I have never seen a piece of aluminum that didn't work. Aluminum can be used for electric wire. But it's not desirable for that application, because of its high intrinsic resistivity, which means you lose too much of the electrical energy when it has to go through aluminum wire. The result is that the wire may get hot, and you'll pay the electric company for more energy than you were able to use for the purpose you needed it.
How do you wire a 100 amp breaker box and a 100 amp safety switch right from the power meter?
Installing a breaker box to the mains is a very dangerous proposition and should only be done by someone who knows what they are doing. It involved removing the meter so that the power is disconnected on the house side, Then the proper size and type of cable is run from the meter to the switch and then to the panel. 3 AWG copper or 2 AWG aluminum is required. The installation would also depend if this were a new additional panel or replacement panel.
Can a circuit breaker be tripped by using 20 amp sockets instead of 15 amp sockets?
A circuit breaker protects the wires that the devices are connected to. If the devices that are connected to the circuit are 20 amps the wire size should be #12 wire fed from a 20 amp breaker. This breaker should not trip unless the circuit is overloaded or a fault occurs on the circuit. If the devices that are connected to the circuit are15 amps the wire size should be #14 wire fed from a15 amp breaker. This breaker should not trip unless the circuit is overloaded or a fault occurs on the circuit. Putting 20 amp sockets on this 15 amp circuit will work but the circuit is limited to the amount of load that can be plugged in. You will not get the full capacity of the 20 socket because the breaker will trip at 15 amps.
Is 6 awg aluminum wire large enough for a Kenmore elite double oven Range which states its Max Amp load is 50 and Min Amp load of 50?
US NEC: 6 awg wire is large enough to supply a 50 amp load but before you use that size it is wise to refer to the wiring tables in the NEC for the recommended wire size to use for the distance from the main breaker panel in a dwelling such as a house or apartment. However, and this is critical, the use of aluminum wire is dangerous and not advised. Most local code will not even permit the use of aluminum wiring anywhere on the load side of the meter, so this could also be illegal. As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed. Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized. IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
