Of course as water is heated it expands and some faucets such as American Standard with the CAP WASHER sometimes open slightly and allow water to drip
To correct the pressure in water pipes, you can adjust the pressure regulator valve. Locate the pressure regulator valve, which is typically found near the main water line or near the water meter. Using a wrench, turn the adjusting screw clockwise to increase the pressure or counterclockwise to decrease it. Be cautious not to exceed the maximum recommended pressure for your plumbing system.
Knocking or hammering on your water pipes is caused by the air chambers within the pipes, which are designed to cussion the pipes against the pressure of the water that flows through them, being depleted to some degree. This is easily fixed, provided that you go about it in the right way--you do not need to call a plumber.First of all, and I can't stress how important this is, you MUST turn off the main water valve in your house to prevent any further water from entering the pipes--do this first.Next, turn on every faucet (tap) and flush all of the toilets until no more water will come out. When you are sure that everything has been drained dry, turn OFF all of the faucets (taps).Now turn the main water valve back on slowly. What this does it to allow the air chambers to be replenished with the correct amount of air to prevent the shock from the water flowing under pressure.
How to reduce your water pressure to your taps if you have a high mains pressure or an unvented cylinder such as a megaflow, boilermate ect. Reducing water pressure in your home can be done in several ways, my video demonstrates a few. Some people turn down the isolation valves or main stopcock which is not advisable, as it can produce noise, water hammer in pipes /taps and can damage the valves and stopcock.
air in the water lines causes banging and whistles/screams. Turn off main water, turn on the faucet, turn main water back on, and it should force the air out.
PRV
install larger pipes
That is your pipes hitting walls or boards. The pipes will move if not properly secured when pressure is removed and applied to them. This pressure change occurs whenever you turn a faucet on or off.
no
High water pressure could be the reason for pipes to rattle when you turn on the outside sprinklers. You may need to have a reducer valve installed.
To correct the pressure in water pipes, you can adjust the pressure regulator valve. Locate the pressure regulator valve, which is typically found near the main water line or near the water meter. Using a wrench, turn the adjusting screw clockwise to increase the pressure or counterclockwise to decrease it. Be cautious not to exceed the maximum recommended pressure for your plumbing system.
Usually you should if your pipes are at risk of freezing. (i.e. you live in a cooler climate and the house has no heat.) The reason for this is that even though your pipes are drained, there is still water in the low spots, which when frozen will expand causing pressure build up. If the air has no where to go it could cause a crack and probably some water damage when ever you do turn on the water. }th0rn{
If we didn't have water pipes I would be out of a job. Water pipes are needed for delivery of the water to a specific place and that is done using pressure and flow using pumps or gravity. Most residential houses don't have domestic water pipes bigger then 1" in size. Almost all water pipes outside of a building are buried in the ground. Every time you turn on a faucet (if on city water) then you could be using water from a water tank many miles away.
This is called water hammer and it occurs when water is running through the pipes at high pressure. To solve this problem you need to secure all piping down properly.
Water Hammer.
It doesn't pump the water in, where the hoses attach to the washing machine is a valve that opens and lets the water in. The pressure in the line forces the water in the same way it does when you turn on a faucet.
The water inside uninsulated pipes may freeze and expand during a cold winter, pushing opening joints or splitting the pipes, often unnoticed. When the thaw comes, the ice in the pipes melt, and the water pressure returns, and the water is able to spray out through the damaged pipes.
The water in your pipes is under pressure so that it comes out of the tap when you turn it on. If there is a hole in the pipe (i.e. a leak) then the water will come out under pressure, the same as if you turned on your tap - if this hole faces upwards then there will be a jet or water like a fountain. The height of this jet is dependant upon the pressure of the water