answersLogoWhite

0

Of course as water is heated it expands and some faucets such as American Standard with the CAP WASHER sometimes open slightly and allow water to drip

User Avatar

Wiki User

14y ago

What else can I help you with?

Continue Learning about Engineering

How do you correct the pressure in water pipes?

To correct the pressure in water pipes, you can adjust the pressure regulator valve. Locate the pressure regulator valve, which is typically found near the main water line or near the water meter. Using a wrench, turn the adjusting screw clockwise to increase the pressure or counterclockwise to decrease it. Be cautious not to exceed the maximum recommended pressure for your plumbing system.


How do you fix water hammering or knocking sounds in a pipe such as a bathroom faucet?

Knocking or hammering on your water pipes is caused by the air chambers within the pipes, which are designed to cussion the pipes against the pressure of the water that flows through them, being depleted to some degree. This is easily fixed, provided that you go about it in the right way--you do not need to call a plumber.First of all, and I can't stress how important this is, you MUST turn off the main water valve in your house to prevent any further water from entering the pipes--do this first.Next, turn on every faucet (tap) and flush all of the toilets until no more water will come out. When you are sure that everything has been drained dry, turn OFF all of the faucets (taps).Now turn the main water valve back on slowly. What this does it to allow the air chambers to be replenished with the correct amount of air to prevent the shock from the water flowing under pressure.


How do you reduce the water pressure in your house?

How to reduce your water pressure to your taps if you have a high mains pressure or an unvented cylinder such as a megaflow, boilermate ect. Reducing water pressure in your home can be done in several ways, my video demonstrates a few. Some people turn down the isolation valves or main stopcock which is not advisable, as it can produce noise, water hammer in pipes /taps and can damage the valves and stopcock.


How do you drain water tank to build pressure?

To drain a water tank to build pressure, first, turn off the power supply to the tank and close the inlet valve to prevent further water flow. Next, open the drain valve at the bottom of the tank to release the water, allowing it to empty partially or completely, depending on your needs. Once the desired level is reached, close the drain valve and reopen the inlet valve to refill the tank, which will help build pressure as the water heats up. Finally, restore power to the tank.


Why do The pipes keep banging while the water is running?

air in the water lines causes banging and whistles/screams. Turn off main water, turn on the faucet, turn main water back on, and it should force the air out.

Related Questions

Surgeing water pressure when you turn on a faucet?

install larger pipes


What is the thud sound when you turn on or off the water?

That is your pipes hitting walls or boards. The pipes will move if not properly secured when pressure is removed and applied to them. This pressure change occurs whenever you turn a faucet on or off.


Does the main water supply have to be turned off and the pipes drained before you can turn the screw on the pressure valve to increase the water pressure in house?

Yes, it is recommended to turn off the main water supply and drain the pipes before adjusting the pressure valve to increase water pressure in the house. This helps prevent damage to the plumbing system and ensures a safe working environment for adjustments.


What caused pipes to rattle when you turn on the outside sprinklers?

High water pressure could be the reason for pipes to rattle when you turn on the outside sprinklers. You may need to have a reducer valve installed.


How do you correct the pressure in water pipes?

To correct the pressure in water pipes, you can adjust the pressure regulator valve. Locate the pressure regulator valve, which is typically found near the main water line or near the water meter. Using a wrench, turn the adjusting screw clockwise to increase the pressure or counterclockwise to decrease it. Be cautious not to exceed the maximum recommended pressure for your plumbing system.


Why does my shower head continue to drip for hours after I turn it off?

The shower head continues to drip because there is residual water pressure in the pipes that pushes out the remaining water even after you turn it off.


How can I effectively deal with frozen pipes?

To effectively deal with frozen pipes, you can try using a hairdryer or heating pad to thaw the pipes slowly. You can also open faucets to relieve pressure and allow water to flow once the pipes thaw. If the pipes burst, turn off the water supply and contact a professional plumber for repairs.


If your water is turned off should you open your faucets?

Usually you should if your pipes are at risk of freezing. (i.e. you live in a cooler climate and the house has no heat.) The reason for this is that even though your pipes are drained, there is still water in the low spots, which when frozen will expand causing pressure build up. If the air has no where to go it could cause a crack and probably some water damage when ever you do turn on the water. }th0rn{


How do I install a water pressure regulator?

To install a water pressure regulator, first turn off the main water supply. Then, locate the current pressure regulator and remove it. Install the new regulator in the same location, making sure it is facing the correct direction. Connect the pipes securely and turn the water supply back on to test the new regulator. Adjust the pressure setting if needed.


How are water pipes needed?

If we didn't have water pipes I would be out of a job. Water pipes are needed for delivery of the water to a specific place and that is done using pressure and flow using pumps or gravity. Most residential houses don't have domestic water pipes bigger then 1" in size. Almost all water pipes outside of a building are buried in the ground. Every time you turn on a faucet (if on city water) then you could be using water from a water tank many miles away.


Why would the water pipes in the ceiling rattle when you turn on the water?

Water Hammer.


How can I replace a water pressure regulator in my plumbing system?

To replace a water pressure regulator in your plumbing system, first turn off the main water supply. Locate the existing regulator and disconnect it from the pipes. Install the new regulator in the same location, ensuring it is securely connected. Turn the water supply back on and test the water pressure to ensure the new regulator is functioning properly.