0
You should add only with a proper load calculation. You should probably have a licensed electrician look at the situation first.
You can find a licensed electrical contractor at www.contraxtor.com to help with your electrical service upgrade
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Does square D make a circuit breaker with a 15 amp and 20 amp breaker in the same breaker?
No tandem breakers are of the same value.
Can you use a 20 amp circuit breaker for an electric dryer?
If you are referring to a cloths dryer, the answer depends on the requirements of the dryer. Most dryers require AWG#10 wire with a 30 amp fuse. If the wiring is AWG#12 then use a 20 amp breaker but never use it on AWG#10 which requires a 30 amp breaker. If you are referring to a hair dryer then yes a 20 amp breaker is fine.
Can you use a double pole 15 amp breaker in place of a 20 amp single pole breaker for a 12000 BTU air conditioner?
If the 12,000 BTU A/C only requires 20 amps to run then yes you can use the same 12 gauge wire but you cannot change it to a 15 amp breaker. You will need to install a 20 amp double pole breaker. If it requires more than 20 amps you will have to replace the wiring and breaker.
Is it ok to exchange a 20 amp breaker with a 40 amp breaker?
No. The 20 amp breaker is probably protecting a #12 wire. Connecting a 40 amp breaker to the 20 amp #12 wire would seriously overload the #12 wire. This means that if the load increased to a full 40 amps the insulation on the smaller size wire would most likely melt off and the wire could short out.
What is the capacity in amperes 20 amp circuit breaker supplying a continuous load?
For a continuous load the circuit breaker is set 25% higher than the load current. So a 20-amp breaker is used with a continuous 16-amp load.
You are putting in a 240 volt 4000 watt heater in a room what size breaker do you need?
20 amp
Can you attach a 20 amp breaker to a 30 amp line?
yes, you can attach. but if the current through the line i.e. through the breaker exceeds 20 amp the breaker will trip. As long as the line carries 20 amp or less there is no problem.
Does square D make a circuit breaker with a 15 amp and 20 amp breaker in the same breaker?
No tandem breakers are of the same value.
New shop 20 amp circuit 32 amp fixture how many fixtures can be put on circuit?
A 32 amp fixture can not be fed from a 20 amp breaker as the breaker will trip every time.
Why does your 200 amp electric panel only have 20 breaker slots?
Some 200 amp breaker panels are made with only 20 slots.
What size breaker should be used on a 20 amp motor?
30 amp breaker with #10 gauge copper wire
What amp breaker for 12-2?
AWG 12/2 requires the use of a 20 amp single pole breaker.
Can you use a 20 amp circuit breaker for an electric dryer?
If you are referring to a cloths dryer, the answer depends on the requirements of the dryer. Most dryers require AWG#10 wire with a 30 amp fuse. If the wiring is AWG#12 then use a 20 amp breaker but never use it on AWG#10 which requires a 30 amp breaker. If you are referring to a hair dryer then yes a 20 amp breaker is fine.
How many 1.2 amp lights can a 20 amp breaker hold?
No more than 13 maximum on a 20 amp circuit.
What breaker for 17.3 amps?
I would suggest a 20 amp breaker. * Added - I would suggest a 25 amp breaker. A slight surge, depending upon what equipment is the source of the 17.3 amp load, should not result in circuit breaker opening. <<>> In North America, the electrical code only allows circuit loading up to 80% on a continuous load. A 20 amp breaker can be legally loaded to 16 amps. A 25 amp breaker can be legally loaded to 20 amps.
Can you use a double pole 15 amp breaker in place of a 20 amp single pole breaker for a 12000 BTU air conditioner?
If the 12,000 BTU A/C only requires 20 amps to run then yes you can use the same 12 gauge wire but you cannot change it to a 15 amp breaker. You will need to install a 20 amp double pole breaker. If it requires more than 20 amps you will have to replace the wiring and breaker.
Is it ok to exchange a 20 amp breaker with a 40 amp breaker?
No. The 20 amp breaker is probably protecting a #12 wire. Connecting a 40 amp breaker to the 20 amp #12 wire would seriously overload the #12 wire. This means that if the load increased to a full 40 amps the insulation on the smaller size wire would most likely melt off and the wire could short out.
