Want this question answered?
You can make squishy putty by using borax, glue, and water! Mix a little of each together, add food colouring, and there you have it! Store in airtight container in fridge. Be careful, this putty stains!
There is many formulas for putty. The putty with the fallowing ingredients of: water, glue, borax solution, and if you want to add, food coloring is a liquid. I know this because, the putty takes the shape of its container, and has all the other properties of liquids. Read bellow for the instructions on how to make it. What you'll need: 2 containers (1 smaller than the other, preferably a film canister) Water Food colouring PVA glue Borax solution (ratio of about 1 Tbsp of borax to a cup of water) Instructions: Fill the bottom of the larger container with PVA glue. Add a few squirts of water and stir. Add 2 or 3 drops of food colouring and stir. Add a squirt of borax (possibly a bit more depending on how much PVA glue you used). Stir the mixture up and put it into the smaller container. By now the mixture should be joining together, acting like putty, crazy putty!
Starting with ordinary silicone rubber sealant add as much ultra-fine graphite powder as it is possible to get the sealant to absorb to make a putty. You will need to add so much that the putty will *almost* no longer be mouldable. Form the putty around a wire and leave to cure. You will now have a carbon rubber electrode. If it does not conduct you have not added enough graphite dust. As some silicone sealant contains fungicide this should not be used on the skin. Adding lighter fluid to silicone sealant thins it down. It may be possible to do this when making the putty to thin it down and get it to absorb more graphite powder. However I have not attempted to thin the mix in this way and as the lighter fluid stays in the silicone putty after curing *never* use this when skin contact is intended.
Usually water and Isopropyl Alcohol and sometimes some aromatic fragrances. Isopropyl alcohol is made up of carbon, hydrogen, and oxygen (C3H7OH), which makes it an organic compound. Isopropyl alcohol comes from wood grain. Rubbing alcohol is typically 70% isopropanol and 30% water. Isopropanol is propane (C3H8) with one of the middle hydrogens knocked off and replaced with a hydroxyl (OH). The formula for isopropanol is C3H8O, or writing the formula to show how the atoms are connected, it would be (CH3)2CH-OH Should be nothing more than isopropyl alcohol and perhaps some water. Some preparations also add some food coloring (green, usually), so it doesn't look like water.
it gets smaller
use a good putty grade resin, add fillers like talc etc , add byk additives & you are done.
Denatured oil is oil that has been changed from the nature or natural qualities of it. It is rendered unfit to eat or drink without destroying usefulness in other applications, especially to add methanol to ethyl alcohol. The denaturing process creates a horrible odor, which is removed by additional heating of the oil at 300F.
You can make squishy putty by using borax, glue, and water! Mix a little of each together, add food colouring, and there you have it! Store in airtight container in fridge. Be careful, this putty stains!
Answer: Wood alcohol is also called methanol, methyl alcohol, Carbinol, wood naptha or wood spirits. It's used as an antifreeze, solvent, fuel and as a denaturant for ethyl alcohol. It's also used for producing biodiesel via transesterification reaction. It can also be used [on occasion] to clean wounds, but is painful.WARNING: Do NOT under ANY circumstances drink isoprpyl alcohol. A drop will cost you the loss of your sight, and any more than that will definitely kill you.(Just thought I should add that in there, in case anyone gets the idea of drinking it - it has happened before.)
OK so first you make the putty then take like an extract for example cherry and you stretch out the putty then add one or two drops of extract and rub together. Glad to help YOU
add sesoning and dont add so much alcohol
To make your own homemade thermometer, a person will need a plastic bottle, a clear straw, some putty, water, rubbing alcohol, and food coloring. Fill a quater of the bottle with equal parts water and rubbing alcohol. Add a few drops of food coloring to help see the change in temperature. Place the straw in the bottle and seal the top completely with the putty, making sure the bottom of the straw does not touch the bottom of the bottle. The liquid will rise and fall through the straw when the temperature changes.
Nothing
There is many formulas for putty. The putty with the fallowing ingredients of: water, glue, borax solution, and if you want to add, food coloring is a liquid. I know this because, the putty takes the shape of its container, and has all the other properties of liquids. Read bellow for the instructions on how to make it. What you'll need: 2 containers (1 smaller than the other, preferably a film canister) Water Food colouring PVA glue Borax solution (ratio of about 1 Tbsp of borax to a cup of water) Instructions: Fill the bottom of the larger container with PVA glue. Add a few squirts of water and stir. Add 2 or 3 drops of food colouring and stir. Add a squirt of borax (possibly a bit more depending on how much PVA glue you used). Stir the mixture up and put it into the smaller container. By now the mixture should be joining together, acting like putty, crazy putty!
Get a candle and use it to heat your putty knife. It will slice though the old putty like butter. Just keep reheating the knife. The best way to soften plumber's putty is to add a little linseed oil and allow it to sit overnight. Knead the putty thoroughly. This won't do if you're in a hurry, so you could try to hurry it along by kneading it with a very small amount of linseed oil (use gloves). Remember to keep the consistency a little bit thicker than Play Doh.
"You need to purchase a pane of glass that will install correctly, then after carefully removing the broken glass and putty, soak the frame in oil, add new putty to allow the window to seal to the frame correctly, then carefully line up and install the pane, using putty again in strips to seal in the pane."
well it's simple you just add.....lets say you want it to smell like almond...just add almond extract! Easy right!!