0
Yes as long as you change the 50 amp breaker to a 15 amp breaker. You will be hard pressed to get the 50 amp #6 wire under the terminals of the 15 amp receptacle.
Wiki User
∙ 9y ago
Add your answer:
Earn +20 pts
240v nema6-50r outlet wired with 6 gauge wire and 50 amp breaker you need to run a heater with a nema 6-30p can you simply put a 30 amp receptical in place of the 50 amp receptical?
Not legally because the rating of the 30 amp receptacle would have a 50 amp breaker ahead of it. If you reduced the feed breaker to 30 amps and still use the #6 wire, this would be within the electrical code rules.
Can you connect a 220 volt stove to a 120 volt circuit?
Yes, this is a safe connection. A range is usually wire rated at 40 amps and the manufactures do not make a 40 amp rated receptacle. The code requires the next highest rated receptacle be used which is a 50 amp rating. This is why the range receptacle is rated at 50 amps. This receptacle is known as a 3 pole 4 wire grounding receptacle, 14-50R 125/250 volt. Black wire to terminal X, red wire to terminal Y, white wire to terminal W and ground wire to terminal G.
How many 50 watt lights on a 15 amp circuit?
50 watt equals less than 1/2 amp current flow at 120 volts so you can have 30 light on a 15amp breaker or 40 on a twenty amp breaker.
Can 50 Amp breaker replace 45 Amp breaker?
Both a 45 amp and 50 amp breaker would require 6 AWG wire. So if you have 6 AWG wire and any devices like an outlet are rated at 50 amps or greater you are okay.
What is the fuse rating for 5MVA transformer?
50 amp
Is there a adapter for a nema 14-30 plug and a nema 14-50 receptacle?
No there are no adapters made for these types of installations. The reason there are no adapters is to provide a factor of safety. To plug a 30 amp plug into a 50 amp receptacle could allow 50 amps to be applied to a 30 amp rated cord. The 50 amp receptacle is more than likely being fed by a 40 amp breaker. Just change the plug cord to match the ampacity of the breaker ahead of the 50 amp receptacle. Or change the 50 amp receptacle and 40 amp breaker to a 30 amp breaker and use your existing cord plug.
Can I replace a 50 amp 240v dryer outlet with a std 15 amp 240 volt outlet?
Theoretically yes if you remove the two pole 50 amp breaker and replace it with a 2 pole 15 amp breaker. This has to be done because the new receptacle is only rated at 15 amps and can not be protected by a breaker any larger than 15 amps.Physically this is not going to happen due to the fact that you will not be able to connect the existing #6 conductor, which fed the 50 amp dryer receptacle, under the terminals of the new 2 pole 15 amp breaker.
Will my electrician need to run new wire from the outlet to the circuit breaker to change from a 50 amp to a 60 amp outlet?
Maybe not. Since there is no wire with a rating of 50 amps exactly there may be 60 amp wire already installed. Range's use a #8 wire with 50 amp range receptacle for its circuit. If the wire that is installed now is # 6, that is good for 65 amps, then no wire needs to be changed. The only 60 amp receptacle that will be allowed on the 60 amp cable is a three pole four wire grounding 125/250 volt device. The number will be 14-60R. There is a three phase rated receptacle in the three pole four wire grounding type. It is a 15-60R.
Can I plug a 30 amp air conditioner in a 50 amp plug?
Yes. Assuming everything is wired correctly and your 30 amp AC cord is compatible with your 50 amp plug, you can do this. I think you will find, however, that your 50 amp plug has a different pin configuration than your 30 amp cord end. This is not easily resolved because there are serious dangers in going the other direction, plugging a 50 amp appliance into a 30 amp receptacle.
Where do I put the red black white and copper wires on a 50 amp three prong recepticle?
The 50 amp receptical will not be a three prong receptacle it will be a 3-pole 4-wire grounding receptacle. It will be a 125/250 volt rating NEMA number 14–50R. The red and black wires connect to the X and Y terminals, the white wire to the W terminal and the ground wire to the G terminal.
Can you use 50 amp wire and receptacle on dyer?
It's necessary to look at the dyer to see how much current it uses, which should be on the maker's plate near where the cable enters the appliance. If it uses less than 50 amps, a 50 amp cable is all right.
What happens if you put a 20 amp 250 V plug into an 50 amp 250 outlet?
You would have a code violation, only a 50 amp/250V plug would fit into a 50 amp/250V receptacle. You would not have proper overload protection, the load could (worst case) call for more amps than it is rated for and catch fire before the breaker tripped.
240v nema6-50r outlet wired with 6 gauge wire and 50 amp breaker you need to run a heater with a nema 6-30p can you simply put a 30 amp receptical in place of the 50 amp receptical?
Not legally because the rating of the 30 amp receptacle would have a 50 amp breaker ahead of it. If you reduced the feed breaker to 30 amps and still use the #6 wire, this would be within the electrical code rules.
Can you connect a 220 volt stove to a 120 volt circuit?
Yes, this is a safe connection. A range is usually wire rated at 40 amps and the manufactures do not make a 40 amp rated receptacle. The code requires the next highest rated receptacle be used which is a 50 amp rating. This is why the range receptacle is rated at 50 amps. This receptacle is known as a 3 pole 4 wire grounding receptacle, 14-50R 125/250 volt. Black wire to terminal X, red wire to terminal Y, white wire to terminal W and ground wire to terminal G.
Can you switch a 30 amp breaker to a 50 amp?
Yes you can use a 60 amp breaker to feed a 100 amp sub panel. The wire from the 60 amp breaker must be #6 or larger. You will not be able to draw the maximum 100 amps from the panel you will be limited to 60 amps.
Can you operate a 30 amp dryer on a 50 amp receptacle?
Yes and no. You can't put a 30A outlet on a 50A breaker as it will be a fire hazard. You can put a 50A outlet on it safely. Then you can plug the 30A load into it, but this is unwise and can be dangerous if you don't put fuses in your pigtail adapter. The best solution: Go ahead and install your 30A outlet but replace the 50A breaker with a 30A breaker. This is the safest and cleanest solution.
Can you use 6-3 NM wire and 50 amp breakers and 50 amp range cord for a 40 amp max load range?
You can if you have the existing materials. If you want to keep your costs down the same installation can be installed with the following materials. For wire all that is needed is 3C #8 wire. For the breaker a two pole 40 amp will work. You will need a 4 11/16" square box to install the range receptacle into.
