0
The #1 remote can be changed to work TV2 if it is the correct model. On the back of the remote at the top will be some writing. If it says IR/UHF Pro, then it can be used for both TV's.
To get it to work the TV2, change the tab in the bottom of the remote that may be a green tab with a 1 in it, or just a green 1, to a blue tab with a 2 in it. This will tell the remote to work the secondary TV. Just readdress it from there and you will be good to go.
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
i am going to buy a new tv lg 37lh20 and want to know if my dish network remote control will work with it.?
Call the Dish Network to inquire about your remote and your new TV: 1 866 869-3109 Customer service can advise you and provide a new remote control if needed.
What is the code for Dynex dx-wbrdvd 1 on Dish network emote?
dish network remote codes for Dynex DX-wbrDVD 1 and proper way to program the control to DVD
What is a Canon remote controller RC 1 used for?
The Canon remote controller RC 1 is used to control the RC 1 remote control car. A remote control car is usually a small car that can be controlled from a distance with a controller.
How do you program dish codes on a element tv?
To control your TV with your Dish Satellite remote, you need to perform a power scan to find your remote code. With your Dish Network remote, follow these steps: 1) Turn on your TV 2) Hold down the 'TV' button at the top of your dish satellite remote (the one that lights up) until all 4 buttons at the top light up 3) Press the large red power button on your Dish remote 4) Press the channel up (on most remotes above the select button in middle) slowly until the TV shuts off 5) Once your Television powers off, press the pound key '#' (at the bottom of your Dish satellite TV remote)
What are the ratings and certificates for LazyTown - 2004 Remote Control 1-22?
LazyTown - 2004 Remote Control 1-22 is rated/received certificates of: Australia:G
How do you change the remote control address on a replacement remote for a Bell Expressvu 4500 receiver?
Dish Network satellite receivers can be programmed to operate on different remote control addresses. Switching to a different address is necessary if you have 2 satellite receivers or if your neighbor's receiver is set on the same remote address and they are changing your channels. # Press the Mode button until the remote is in the SAT mode. # Press the Address button once (the SAT mode light will start flashing). # Use the numeric key to enter an address between 1 and 15 (do not put a 0 in front of single-digit addresses; 1 is the default remote address). The SAT mode light will stop flashing and stay lit. # Press the Address button again to save the change to the remote control. If you entered a valid remote address, the SAT mode light will blink 3 times. # Make sure the satellite receiver is Powered-off. If not, power the satellite receiver off and wait 15 seconds. # Press the Info button on the front of the satellite receiver. This will bring up the "Important System Information" menu. # Press the red Record button the the remote. The screen will update and the "remote address" listed on the screen will change to the new remote address of the remote control.
What are the release dates for Chase - 1973 Remote Control 1-20?
Chase - 1973 Remote Control 1-20 was released on: USA: 27 February 1974
What are the release dates for LazyTown - 2004 Remote Control 1-22?
LazyTown - 2004 Remote Control 1-22 was released on: USA: 2 August 2005
What are the release dates for Life Remote Control - 2011?
Life Remote Control - 2011 was released on: USA: 1 December 2011 (DVD premiere)
How do you get a 20af44 toshiba TV to change to channel video 1 without a remote?
There is no way to change the input without a remote :(.
What channel does the symphonic tv have to bE on to be programmed with remote contro for dish network?
To program the remote control, the TV just has to be on. There's no specific channel required to do so. In case it is needed, I have included the steps to program a remote control on DISH below! Addressing Remote to TV: 1.) Press and hold the clear TV button until all mode lights light up. 2.) Release and TV light will be blinking. 3.) Enter code and press #. The TV button should flash 3 times. 4.) Try functions (Volume, Power, etc..) and see if it is working. 5.) If no function, repeat steps 1-4 with another code.
What are the codes for a 8 in 1 jumbo decibel electronics remote control to a lg tv?
What are the codes for jumbo remote
