0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you repair flex pipe on exhaust?
You need to replace it by welding a new flexpipe in its place. Flex pipes have too much heat to be glued or wrapped.
Where can you purchase just the flex pipe for a 1995 Camry?
A GOOD MUFFLER SHOP LIKE MEINEKE CAN CUT OUT THE BAD SECTION OF FLEX PIPE AND WELD IN A NEW ONE. USUALLY TH PIPE IS AS GOOD OR BETTER THAN NEW.
How do you repair an exhaust pipe clamp on a 98 Pontiac grand am gt?
You can replace an exhaust clamp with a new one.
Colonial New York's weather?
If it is a pipe that is not easily cut out and replaced, you can use a pipe clamp. Wrap the clamp around the pipe and tighten the two bolts to compress it around the pipe. If it is a drain pipe as you say, there is very little pressure on t he line, so the clamp should work fine.
How much does it cost to replace a flex pipe on a 1999 ford escort?
It's cheapest to buy a universal pipe and weld it on yourself. The universal flex pipe part is Walker 42216. It goes for $25-$30. If you bring the pipe to a shop, the shop should charge you around $50-$80+tax in labor to remove the old pipe and weld the new flex pipe in.
How does a flex pipe on a 1995 Saturn SL1 get replaced?
Front wheel drive vehicle engines move when you accelerate and decelerate, so the exhaust system must flex with it. These engines are equipped with a front exhaust pipe with a flexible section, which accommodates this movement. When replacing this pipe, you must cut the old pipe between the flex section and the Catalytic Converter. Purchase a new front pipe from the parts store, and with it a short "coupling" piece which will be slightly larger in diameter, so to fit over the two pieces. You will also need two clamps sized to fit over the coupling. Install the new front pipe, with the short coupling at the joint with the old section just forward of the converter. You then clamp the two ends of the coupling to complete the repair.
How do you fix the flex pipe on a 1992 Honda Prelude?
replace with a new pipe new gaskets and bolts must torch out old bolts from cat Take it to a muffler shop
How do you replace the flex pipe on the exhaust system of a 1992 Nissan Maxima?
The flex on the 1992 maxima is not, to my knowledge, replaceable. What you need is the front pipe and associated gaskets and bolts/studs. I had mine replaced 2 months ago, runs great. if old bolts/studs are thinthen you need new ones. try eBay for the front pipe, got mine for $100. beware of broken manifold gaskets and studs because the removal of the front pipe might jolt some stuff around.
How to replace radiator hose on a Chevrolet Corsica?
The radiator hose is held in place with a clamp on each end of the hose. Turn the clamp screw to the left. The clamp will become loose in the hose can be removed. Reverse the process to install the new radiator hose.
How do you change the battery on a 1992 Toyota Camry?
disconnect the battery cables. find the battery clamp and remove it. Lift the battery out, then set then new one in place. Install the clamp, then connect the battery cables.
How do you replace the muffler on a 1989 Camaro RS and how difficult is it to do?
to change the muffler is really easy as long as u don't have to much rust unger it. all u need to do is take off the clamp that comes from the exhaust pipe and then the one clamp on the other side on the tail pipe. which is easier if u take it right off from the car and put back on later then if the rust isn't to bad the pipe would slide right out of the muffle. leaving u to put on a new one
What can I do to be safe when I am hooking up a new flex line to an existing gas line which does not have a shut off valve?
Either shut the gas off at the meter or install a valve on the pipe. As long as you don't have an open flame somewhere close to the gas line and have everything ready, you can take the current flex line off and install the valve with little gas excaping. Use pipe dope on the threads of the pipe instead of Teflon tape. This lets you cap the pipe with your thumb while you apply the pipe dope. Then just install the valve and tighten, making sure to hold the pipe so that you don't disturb the next joint further down the line.
