0
Yes, the 440 volt motor is withing the 10% voltage range of the 460 volt group. When the supply is said to be 480 volts, usually it is lower than what it is stated to be. Once the motor is connected check the current against the motor's nameplate amperage.
Wiki User
∙ 11y ago
Wiki User
∙ 11y agoYES
Add your answer:
Earn +20 pts
What is the circuit for reversing an electric motor?
I HAVE A SMALL ELECTRIC CLOCK MOTOR THAT I NEED TO REVERSE. WHAT IS THE CIRCUIT I NEED TO REVERSE IT?
What is an electric circuit that controls another electric circuit through a relay?
Remote-Control Circuit. Any electrical circuit that controlsany other circuit through a relay or an equivalent device.
What causes electrical overloads?
Electrical overloads are caused by the load amperage increasing above what it should normally be. On a motor load this could be a request for the motor to do more work than the motor is capable of, working outside of its HP rating. In a house circuit an overload is created by plugging more devices into the circuit than the circuit breaker can handle. Again the load current will be higher than the circuit will allow and the circuit will open by the tripping of the breaker.
Will a 15 A circuit breaker trip if a 15 ohm toaster is turned on in a circuit that already has a 0.20 hp motor and three 100 W light bulbs and a 600 W electric iron?
A 15 Amp breaker should trip when concurrently you connect to it a 15 Ohm toaster (8A), a 0.2 HP motor (2A), three 100W incandescent lamps (2.05A), and a 600 Watt iron (5A).
How to connect 3 phase power factor correction capacitor?
how to connect power capacitor with 3 phase motor
Will the circuit with two batteries a bulb and a motor work?
If you will connect it right, it will work.
What is a motor in a circuit?
A motor in a circuit is classed as the circuit's load.
How to connect a mechanical load to a motor?
To connect mechanical load to a motor, you couple it to the shaft of the motor.
How do you install a 95 contour sunroof motor?
Connect the sunroof motor with the sunroof motor retaining bolts. Connect the sunroof linkage. Connect the wiring harness to the back of the sunroof motor.
How can a voltmeter be constructed using a galvanometer?
pp you can use the R motor from a hard drive. note this motors don't work for testing current.
If you have a DC passing through a circuit will the current decrease when you add a DC motor and if so by how much?
In the circuit where the DC motor is added, it was not specified whether the motor was added in series or in parallel to circuit elements. If it was added in series, it will increase circuit resistance and it will cause circuit current to go down. In parallel, the motor will reduce total circuit resistance, and circuit current will increase.
What is the circuit for reversing an electric motor?
I HAVE A SMALL ELECTRIC CLOCK MOTOR THAT I NEED TO REVERSE. WHAT IS THE CIRCUIT I NEED TO REVERSE IT?
Which is not a type of home circuit?
A three phase motor control circuit.
Is tram close circuit or open circuit?
If the circuit was open, the tram's motor could not run!
Why is a motor needed in a circiut?
A motor is not needed in a circuit, a motor is an electrical load for the current to drive, but the circuit can perform with other types of load - such as a lamp, a transformer, a heating coil, or any electronic load. if you mean 'why does an electric motor need a circuit?' this is because the motor is an electrical device which has coils of wire to produce a magnetic field, without the circuit it cannot function.
How do you connect a motor to a computer and how would you control it from python?
A motor can be connected to a computer through some type of controller circuit. Typically, such a circuit would receive input from the computer that indicates the direction and speed of the motor, then the controller would convert that to the appropriate pulses and voltages that would cause the motor to respond properly. Depending on what you are trying to do, consider a "stepper" motor, which has 3 inputs. When power is applied to any 2 of the inputs, the motor will "step" forward a few degrees. The controller determines the motor speed by firing power transistors in the appropriate sequence to cause the motor to operate. A less sophisticated approach is to simply turn a motor on by engaging an output transistor that operates a traditional motor. The transistor could even activate a relay if you are uncomfortable with transistor circuit design. A popular electronic development platform is called the Arduino. It would be trivial for your Python program to send a command to the Arduino which would control the circuit.
Why current is supplied to DC motor?
What supplies a dc motor is not current, but voltage. Current is what flows in the circuit formed by the dc motor and for the charge. That current varies according to the resistance of the circuit.
