0
What else can I help you with?
If a light bulb is missing in a series circuit will the bulb light?
If one light bulb in a series circuit fails, all the other light bulbs will go out, until the failed bulb is replaced and the series circuit is completed again.If one light bulb in a parallel circuit fails, all the other light bulbs will still work.
What materials are conductors in a torch?
The conducting path of a torch is a simple circuit: Battery to switch, switch to bulb, bulb back to battery. Provided the switch is on, and there are no breaks in the circuit wiring (and the bulb is good), the torch should work.
Give two possible reasons why their circuit does not work when they close the switch?
The cell has no more electricity and the bulb has blown.
What happens when one light bulb burns out in a series circuit?
All of the light bulbs in the series circuit would go out.
What are all the parts on a circuit board?
to assemble a circuit you just need to connect one end of a wire to the battery and the other to the light bulb ( could be another electrical device) now take an other wire and connect on end of it to the other side of the battery and the other to the other side of the light bulb( or an other electrical device. if your circuit is including a switch this is how you do it: ( you will need three wires for this circuit if you have one electrical device) connect one end of the wire to the battery and the other to the switch.Grab another wire and attach one end of it on the other side of the switch and the other to the electrical device (light bulb). Grab another wire and attach one end of it to the other side of battery and the other to the other side of your electrical device. And there you have it how to assemble a circuit
How does an ice bulb work?
The led glow when it is attached to the batteries.
Where would you put an ammeter in a circuit?
in a series circuit or it will not work. Put it after the bulb
If the filament of the bulb is broken would the circuit be complete?
If the bulb's filament is broken, the whole circuit becomes open. If the bulb is in a series circuit or is the only bulb, the electricity would no longer flow. If the bulb is in a parallel circuit, along with other bulbs, then only the blown bulb would go out, and the other bulbs would still work.
Does putting batteries in the dark work?
It depends on wether it is connected to a circuit
Why does short circuit break whole circuit?
Because a whole circuit needs a short circuit to work. It's like a remote; the remote is the whole circuit and the batteries needed are the short circuit. if those batteries are broken, the remote won't work. In other words, without a short circuit, a whole circuit can not occur successfully. Hope this helped, Charlie the Grey
Why the don't flashlight work?
Dead batteries, dead bulb, broken switch.
What has to be in plce for a circuit to work?
For a circuit to work, it needs a power source (such as a battery), conductive pathways (wires or circuit traces), a load (such as a light bulb or motor), and components like resistors, capacitors, and transistors to control the flow of electricity. Additionally, the circuit must be closed or complete, meaning that there is a continuous pathway for the electricity to flow.
How does a flaslight work?
A flashlight works by converting electrical energy from batteries into light energy through a bulb or light-emitting diode (LED). When the switch is turned on, the circuit is completed, and the electrical current flows through the bulb or LED, causing it to emit light.
If a light bulb is missing in a series circuit will the bulb light?
If one light bulb in a series circuit fails, all the other light bulbs will go out, until the failed bulb is replaced and the series circuit is completed again.If one light bulb in a parallel circuit fails, all the other light bulbs will still work.
What are the differences between a parallel and series circuit when it comes to connecting batteries?
In a parallel circuit, batteries are connected side by side, allowing each battery to provide power independently. In a series circuit, batteries are connected end to end, increasing the total voltage but requiring all batteries to work together to provide power.
What will happen if you try to complete a circut by joining the glass of a light bulb to the batttery?
The glass of the light bulb is not conductive, so the circuit would not be completed. You would need to join the wires to the positive and negative contacts on the base of the bulb for the circuit to work.
How would you troubleshoot a light circuit that does not work?
Tail light doesn't. Work with new bulb in
