0
If you mean can you plug a radio into an outlet controlled by a light switch, the answer is yes, provided the radio does not draw more current that the circuit can supply. (This would not apply to your standard household radio, but only to a high powered unit.)
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
How do you connect an ON-OFF switch to control the light?
To control a light with a switch, the switch has to be connected in series with the light fixture.
How do you connect a switch to a light then another light to a switch and have the switch work only the light on its end?
go to the Help option in Matlab. It will not help at all.
Remove radio 1999 Nissan Sentra?
Look in between the hazard light switch and the rear window defrost switch. there should be a cover you can pry up with a flat head screwdriver. remove that and the screw that is underneath it. Then remove the bezel that covers the radio and a.c controls. There will be wires attached to the hazrd light switch and the defrost switch. remove the connectors that connect them. then there are four screws holding in the radio just remove those and slide the whole thing out.
How can you short out a radio?
Remove the radio's covers then place a piece of wire on the back of your radio's motherboard. Connect your radio to electricity and switch it on. I hope you see a nuclear explosion.
How do you hook up a switch to a light using a marine battery?
Hey. Same as any battery. Connect the Negative terminal straight to the Negative on the light (if needed), Normally the outer rim of the globe. Connect the positive terminal to the switch, then from the other plug on the switch to the positive terminal to the light. Done.
How can you make music come on with a light switch?
You can make music come on with a light switch the same way you can make a light bulb come on - plug a radio into the switched outlet.
Where is the cold side of the stoplight switch on a 2005 Chevy silverado?
Use a test light to determine Connect to ground and one side of the switch - if the light illuminates that is the HOT side if light does not illuminate that is the COLD side of switch
Where is the fog light button on a 2000 ford explorer?
The fog light switch is in the center stack of the dash , just to the right of the radio , near the bottom of the radio
How do you connect multiple lights to one switch starting at the light?
You put switch in series with the black supply wire and the black wire to the first light. Then connect black wire of first light to black wire of second light, black wire of second light to third light and so forth. Do the same with the white wires and ground wires.
How do you wire a basic off switch to a light?
Light switch connection is usually straight forward. Find your incoming hot wires, black and white. With the switch in the off (down) position and the power disconnected , connect the black wire to the top screw of the switch. Find the load wires and connect the black to the bottom screw of the switch. Connect the two remaining white wires together with a wire nut and push them to the back of the switch box. Install the switch into the wall box, replace switch plate cover. Turn the breaker (power) back on. Flip the switch to the up position and the light should come on.
How do you hook up one light to one switch in a basement lighting system that has all 10 lights connected to one switch?
If you have good access to the wiring this is relatively easy to do. Each of the 10 lights is connected to another in parallel in a "daisy chain" fashion. Light 1 is connected to the switch, light 2 is connected to light 1, light 3 is connected to light 2 and so forth. Let's say it is light 5 that you wish to switch separately. You can first install the new switch by either adding a new box or modifying old switch box. There are two gang switches that will fit the form factor of a single switch. TURN OFF THE POWER TO SWITCH BOX. Using the same supply input at original switch, add a new black wire to the wire nut for input to original switch and connect this to the input of new switch. Then run a new wire to light 5 and connect black wire to the output of new switch. Connect all the white wires together in switch box and separately connect all bare wires together in switch box. Now at light 5 undo the black and white wire coming from the fixture, and reconnect the wire nuts so that there is a direct connection between light 4 and light 6. Do the same for the ground if present (bare wire). You now have the fixture wires hanging free. Now connect the black wire from new switch to the fixture black wire and white to white and you are done.
How do you connect two way electrical switch?
The two way switches work in pairs. We find most of them in our houses where the light bulb can be operated by two switches each at the far end to the other. Each switch consists of three terminals two of which are connected. When one switch is open and the other is closed then the bulb glows and viceversa
