Want this question answered?
you probably can't, you need a neutral and a live wire to make a fan work. switches normally only have live wires.
Your question sounds simple but it isn't. There are two ways of wiring a light to a switch. One is to bring the hot and neutral wire to the switch box and from there run wires from the switch to the light. If this is the case you can install a GFCI on the circuit. The other way is to bring the hot and neutral wire to the light and from there run two wires to the switch and switch the light that way. In this case you cannot install a GFCI to in the switch box. <<>> The way you want the circuit to work has to be laid out as follows. Method one, the circuit that now controls the bathroom devices can be changed to a GFCI breaker. This is probably the quickest and cheapest, unless the job is new construction. Method two, if new construction use this method, as tearing walls open to get to the wiring will become costly. Where a supply circuit comes from the service distribution panel the first device on that circuit has to be a GFCI receptacle. This device has secondary terminals on it, that if connected every device downstream from it will also be protected. So if you supply the two way light switch that controls the vent fan and a bathroom light from the secondary terminals from the GFCI receptacle they will be protected.
To control a light with a switch, the switch has to be connected in series with the light fixture.
A licensed electrician can install a timer on your light.
If you have good access to the wiring this is relatively easy to do. Each of the 10 lights is connected to another in parallel in a "daisy chain" fashion. Light 1 is connected to the switch, light 2 is connected to light 1, light 3 is connected to light 2 and so forth. Let's say it is light 5 that you wish to switch separately. You can first install the new switch by either adding a new box or modifying old switch box. There are two gang switches that will fit the form factor of a single switch. TURN OFF THE POWER TO SWITCH BOX. Using the same supply input at original switch, add a new black wire to the wire nut for input to original switch and connect this to the input of new switch. Then run a new wire to light 5 and connect black wire to the output of new switch. Connect all the white wires together in switch box and separately connect all bare wires together in switch box. Now at light 5 undo the black and white wire coming from the fixture, and reconnect the wire nuts so that there is a direct connection between light 4 and light 6. Do the same for the ground if present (bare wire). You now have the fixture wires hanging free. Now connect the black wire from new switch to the fixture black wire and white to white and you are done.
It is quite easy to install the 1992 Chevy Lumina brake light switch. The brake light switch simply plugs in and out.
How do you install a stop light switch on a 1972 cougar
It is very simple to install a dimmer switch in place of a regular light switch.
Most people can install an bathroom vanity light if the electrical box and light switch are already installed. You just need to make sure you turn of the power while you are installing the light and be certain that you are attaching the wires correctly. If you are not comfortable installing the light fixture on your own, or if you need to install the electrical box for mounting and the light switch, then you will need to contact a licensed electrician to install it for you.
I have a 1998 Chevy 2500. I would like to know how to install the brake switch, and does the switch affect tran from park to drive in shifting?
where location of brake light switch on 1989 chev, truck.
Reach under the dash at the switch. There is a small button on the side of the switch, push it in and remove the light switch knob. The switch is fastened to the dash by the round nut with a slot on each side of it.
Look under the dash on the 1996 suburban, and locate the brake light switch on the brake pedal arm. Remove the switch nut, and slide the switch out. Unplug the wires from the switch and install the new switch.
Remove the wiring harness from the back of your 1997 Ford Crown Victoria hazard lights switch. Remove the hazard light switch retaining screws. Reverse the process to install your new hazard light switch.
check with the dealership there was a recall to replace the switch for free! I had mine replaced...tombo
The switch is easy to install. Its down by your break pedel simply twist it and it comes out. The stop light extension harness has a little metal bar on it. Push this down and the switch pops right off.
If it is the main switch for the lights, 1, make sure the lights are off 2, push the light switch in and turn towards sidelights at the same time 3, pull the switch out when fitting the new switch just push into place.