0
Can you read 120 volts line to neutral even with a severed neutral?
Wiki User
∙ 11y ago
It depends on what side of the break that you are reading from. On the neutral load side of the break there will be no reading. On the panel neutral side of the break you will get a reading.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
Would the black wire be line 1 on 240V line in?
On a 240 volt circuit both line wires are hot, so they may both be black, depending on the wire used. There is normally no neutral required unless you are also tapping off 120 volts between hot and neutral.
Is 277 volt one hot wire?
No, 277 volts is the line to neutral of a 480 volt wye three phase system. L1- N, L2 - N and L3 - N will give you 277 volts. L1 to L2. L2 to L3 and L3 to L1 will give you 480 volts.
What is the Equipment Demand Load for a 12 kW kitchen range line and neutral?
The demand load would be 12 kW. When you talk about line and neutral you are referring to the voltage that the equipment operates on. In North America, an electric kitchen range operates on two voltages 120/240 volts. The 240 volts is obtained across two breakers in the distribution panel and the 120 volts is obtained between either 240 volt leg and the neutral. On a range of this size the 120 volts is usually used for the clock and controls for the range. The range at maximum would draw 50 amps, fed by a two pole 50 amp breaker using a #6 copper conductor with an insulation factor of 90 degrees C. The range will have an internal breaker or fuse to protect the 120 volt circuit.
How many volts does a mains plug use?
This completely depends on whereabouts you live. For example: In the UK = 230 V In the USA =120 V It is less in the USA because they think it is safer, this is nonsense because anything over 60 volts will kill you. As in the US and Canada, UK sockets have three contacts: line, neutral, and protective conductor (earth). The line and neutral contacts are protected from interference by the use of shutters that are opened by the plug's earth pin.
What is the normal voltage of house electricity in the US?
The voltage in North America can be as low as 110 and as high as 125 volts. The average is about 115 to 117 volts. <><><>><> House voltage in the US is generally 120v line to neutral and 240v line to line. It is referred to as a "120/240v single phase service." Actual voltage can be as low as 110/220 or as high as 125/250.
What is voltage between earth and line?
In a typical residential situation there is 220 to 240 volts between the two hot wires that are typically red and black and 110 to 120 volts between neutral and either black or red. The voltage between neutral and earth should be zero.
Why 380 volts line to line if connect line to neutral is 220 volts?
A voltage of 380 volts is a three phase voltage. On a three phase four wire system, each phase leg to neutral (grounded) will give you 220 volts. This voltage is obtained by dividing the phase voltage by 1.73, as the phase legs are generated 120 degrees from each other. Square root of three is 1.73 divided into 380 equals 220 volts.
What is an AC single phase 2 wire system?
two wires coming off the secondary of the transformer ex. residential voltage of 120 volts each line, and one neutral wire, L1 to neutral is 120 volts, L2 to neutral is 120 volts, L1 to L2 is 240 volts.AnswerA single-phase, two-wire, system comprises a line conductor and a neutral conductor. In European countries, the line conductor for a residential supply is at a nominal potential of 230 V with respect to the neutral.In North America, a 'split phase' system is used for residential supplies; this is a single-phase, three-wire, system comprising two line conductors which and a neutral conductor. The nominal potential difference between the line conductor is 240 V, while the potential of each line conductor with respect to the neutral is 120 V.
What is the peak to peak voltage for the AC line voltage in normal outlets of your house?
Peak - neutral for 120 volts RMS is 169 volts, or 120 * sqrt(2) Peak to peak will be 2 x this value, or 339 volts.
What is single phase 480?
The utility company can provide a 480 volt, single phase service from a single phase transformer, usually with a three wire service. 480 volts is measured between the two line conductors, and 240 volts is measured between either line conductor and the common neutral conductor. The voltage of the line conductors are at 180 degrees with respect to the neutral conductor.
What should be the primisable voltage between neutral and earth in a three phase system?
It is the line to line voltage divided by 1.73. 600V / 1.73 = 347V 480V / 1.73 = 277V 380V / 1.73 = 220V 208V / 1.73 = 120V
How do you wire 250 watt metal halide 277v with only one line and one common?
That is all that is needed to wire the fixture. The 277 volts is the line to neutral of a 480 volt three phase system. Any one of L1, L2 or L3 to the neutral will give you the 277 volts that you need to connect the fixture so that it will operate.
Does a 208 volt outlet need a neutral?
No a 208 volt outlet does not need a neutral. 208 volts is the line voltage between any two legs of a three phase 208 volt system.
Would the black wire be line 1 on 240V line in?
On a 240 volt circuit both line wires are hot, so they may both be black, depending on the wire used. There is normally no neutral required unless you are also tapping off 120 volts between hot and neutral.
Does a 480 volt panel have a neutral bus?
Usually yes. A typical 480 volt panel is a 3 phase panel with 480 volts line-to-line and 277 volts line-to-neutral. However, I did once see a panel that was 480 volts, 3 phase, but because it served only motors it did not have a neutral. (a 3 phase motor doesn't use a neutral.) Similarly, if a panel uses only 2 legs of a 3 phase 480 volt system, which would be called single phase, it would not require a neutral if it only feeds 480 volt single phase loads. But I find the idea of no neutral to be extremely unusual and in my one personal experience, I blamed it on the age of the system. In 16 years of commercial and industrial construction I have never installed a 3 phase panel without a neutral and all my work is designed by engineers.
How connect a transformer 380 volt 3 pH to 220 volt mono pH?
any one of the three line to neutral is 220 volts
What to do when there is voltage at neutral?
Quality of the earth pit needs to be checked and enhanced. Check the continuity of the earth bus/ conductor, check for improper joints in the earth bus / conductor and correct it. Earth resistance will reduce and the voltage difference between neutral and earth will also reduce. Check also for the loose or floating neutral and correct it.
