Want this question answered?
A 5-amp fuse is designed to fail if more than 5 amps goes through it. A 6-amp fuse does likewise with more than 6 amps. Therefore, if you replace a 5-amp fuse with a 6-amp, you might be leaving components vulnerable to damage and wiring vulnerable to overheating, which could start a fire. If you replace a 6-amp with a 5-amp, the fuse will burn out if the circuit is drawing between 5 and 6 amps.
fuse number 1 is 10 amp fuse 2 is 25 amp fuse 3is 25 amp fuse 4 is a spare fuse 5 is 10 amp fuse 6 is a spare fuse 7 is 20 amp fuse 8 is 25 amp fuse 9 is 20 amp fuse 10 is 5 amp fuse 11 is 5 amp fuse 12 is a spare fuse 13 is 5 amp fuse 14 is 15 amp
7.2kW shower = 32 Amp fuse = 6 mm2 cable size7.5kW shower = 40 Amp fuse = 10 mm2 cable size8.5kW shower = 40 Amp fuse = 10 mm2 cable size9.5kW shower = 40/45 Amp fuse = 10 mm2 cable size10.5kW shower = 45 Amp fuse = 16mm2 cable size
I think in most applications the difference between 6.3 amps and 7 amps is meaningless. However, if your equipment calls for 6.3 amp protection, 7 amps may allow your equipment to burn up before the fuse blows.
You could, but it would be safest not to. A time delay fuse will allow for a short (12 seconds or less) spike in the current (up to three times the rated current for the fuse). This happens when you start up a motor, or a compressor, etc... If you were to replace a regular fuse (say 2 amp) with a time delay fuse (also 2 amp), then instead of breaking the circuit at 2 amps, the circuit will go 12 seconds at 6 amps before shutting down. This could easily start a fire, so for your safety, it is best to replace a fuse with the exact same kind that came out of it.
interior fuse box above the hood release. Its fuse #6 (7.5 amp)
There are 2 fuse panels . One is located on the side wall on the passenger side of the drivers side they are all clearly marked as to what each fuse is for . There is a fuse removal tool located inside the fuse panel . look on the door of the panel to identify which is for the wipers , It is usually the bottom fuse (20 amp) on the bottom left side of the panel . Using the fuse tool remove and inspect the fuse , even if the fuse you have taken out still looks good replace it with a new 20 amp fuse. The other fuse panel is located under the hood and is located on the drivers side of your car . The panel is about 6 inches long and 8 inches wide, remove the cover and turn it upside down it shows you where each fuse is located ,remove the windshield wiper fuse and replace with a new one
The 1996 Ford Probe owners manual shows : fuse # 6 - 15 amp - audio system , dome and map lamps , etc. fuse # 7 - 15 amp - audio system , power mirrors fuse # 8 - 15 amp - audio system , cigar lighter
That fuse should be located in the driver's side kick panel remove door with a tug on the small knob on the door it will be fuse number 2=15 amp (tail) number 6=15 amp(stop) or number 7=7.5 amp (turn)
Yes, that is safe.
a 6.3 amp 125 volt fuse a 6.3 amp 250 volt or 300 volt is fine with similar time delays depending on application it may be easier to find a 10A it should still protect most of the components
The fuse panel located under the hood, called the battery junction box, fuse position #6 which is a 15 amp fuse.