0
Yes, but it's not a good idea. It's designed for indoor use. And the building codes in your area may forbid it.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
What is conduit wiring?
Conduit wiring is synonymous to wires in a pipe.
Is an equipment ground required in PVC conduit?
Generally, when using PVC conduit you should also run a ground wire.
What are some examples of a tee joint in the electrical trade?
A tee joint in the electrical trade is a conduit fitting. It is used in conduit work where there needs to be a device connected into the main conduit run. An example of this is where a light switch needs to be installed into the conduit run. The main conduit run starts at the distribution panel and proceeds to a lighting fixture. On the way a switch is needed to operate the light fixture. In the main conduit run a tee fitting is installed so as to pick up the switch for the fixture. When the conduit system is complete the wire is then drawn in. The "hot" conductor is pulled to the tee fitting and then diverts to the switch box to pick up the switch and then back up the same conduit to the tee fitting and then on to the lighting fixture. Splices are not usually made in tee fittings.
What is best used to mark out the conduits run?
Chalk line is used to mark out the ''conduit run''
How to wire a house with cinder block exterior?
There are several options:First, you can install conduit into the block as the house is being built and cut out for the outlet boxes.Second, you can use furring strips to create a space between the block and the drywall of the inside surface.Third (if you aren't so concerned about appearance) you can surface mount conduit and outlet boxes on the block.Answer for USA, Canada and countries running a 60 Hz supply service.In addition to the suggestions made above I add the following considerations:Running conduit in the block is the way commercial and industrial installations are often made. This takes some cooperation with the block layers because they generally will not run the conduit for you and you have to be cooperative with him/her on how much conduit to add at any one time as the wall is built.If a wall is already built and if it is not slugged (filled with mortar) you can add wiring by running the wire overhead (above ceiling) and into the wall through holes made in the block above the location of devices.The code allows required outlets to be placed in the floor within 18 inches of the wall. You may place outlets anywhere you need them, but only the ones within this distance will count for satisfying the code for required outlets. This is not preferable, putting outlets in the floor, but it is allowed by the NEC.There are various products on the market designed specifically for surface mounting in finished installations, such as homes or offices. The most common brand name is Wiremold, and though this is a brand name, the term wiremold is often used as meaning any of these products.Any surface mounted installation, whether conduit or wiremold, can be painted to help it blend into the decor of the room.Of all the options discussed here I like the furring option the best. It seems to be the least troublesome and simplest option given.
What is conduit wiring?
Conduit wiring is synonymous to wires in a pipe.
Can you run 110 and 220 volt circuits in the same conduit?
Yes, 120 and 240 volts can be run in the same conduit.
Can 480 volt electric be run in emt conduit?
Yes 480 volt electric wiring can be run in emt conduit.
Can a three phase circuit be installed in the same conduit or in different conduits?
The conductors of any three phase circuit must be run in the same conduit. If the circuit requires a neutral, it must also run with the conductors in the same conduit. (If they were to be run in more than one conduit or raceway, the circuit would not operate properly.)
Are bushings required on 500 and 700 series wiremold?
Yes. Especially after a length is cut. I usually file the end and then use the approved Wiremold bushing.
Can you run parallel 4 ought aluminum conductors in the same 4 inch conduit?
Yes. Actually they should be run in the same conduit. You don't ever want to run parallel separately.
How many bends in a conduit run would be required before the use of a pull box?
There has to be a pull box between every four quarter bends in a conduit run.
Does the Nec allow grounding electrode conductor to be run in conduit that has other conductors in the conduit and what code section?
No, the bare copper grounding conductor can not be in a conduit with other conductors. It can be in conduit by itself to provide mechanical protection for the wire.
Is an equipment ground required in PVC conduit?
Generally, when using PVC conduit you should also run a ground wire.
Should you run conduit parallel with the building if the fastest way is diagonal across the building?
Souldryou run conduit parallel with the building if the fastest way is diagonal across the building
What combinations of bends in a conduit run require the use of a pull box?
Code states no more that 4 - 90 degree bends in a conduit run between pull boxes.
What are some examples of a tee joint in the electrical trade?
A tee joint in the electrical trade is a conduit fitting. It is used in conduit work where there needs to be a device connected into the main conduit run. An example of this is where a light switch needs to be installed into the conduit run. The main conduit run starts at the distribution panel and proceeds to a lighting fixture. On the way a switch is needed to operate the light fixture. In the main conduit run a tee fitting is installed so as to pick up the switch for the fixture. When the conduit system is complete the wire is then drawn in. The "hot" conductor is pulled to the tee fitting and then diverts to the switch box to pick up the switch and then back up the same conduit to the tee fitting and then on to the lighting fixture. Splices are not usually made in tee fittings.
