0
Can you use a 16vac 4A power supply to power a 16vac 1000ma tube amp?
Wiki User
∙ 8y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How much electricity power does a vacuum tube use?
not enough
What is a graduated cylinder brush?
It is a lab safety supply. It is used to clean the inside of a graduated cylinder after it is used. A graduated cylinder is basically a test tube with markings indicating the volume of the matter in the tube.
What material used in boiler tube in indian power plant?
Usually Alloy steel is used, copper and brass are also used as boiler tube materials
Where to buy a clear plastic tube in local stores?
Any well-stocked hardware store will have clear plastic tube available in several different diameters, usually in or near the plumbing-supply section, and priced per foot.
What is a good replacement for overhead fluorescent lights?
The best replacement is a new fluorescent light tube of the right voltage and power.
Can I use a 16vac 4A power supply to power 16vac 1000ma tube amp?
Yes, 1000 ma equates to 1 amp. The 4 amp power supply will have more than enough capacity to operate any device drawing 1 amp.Just make sure that the voltages match. AC voltage of the power supply to AC voltage on the device. You can not cross voltages using a DC power supply to operate an AC device, or the other way around, an AC power supply to operate a DC powered device, even though the voltage values are the same.
Can the amplified output of the transistor exceed the range of power supply given to it?
No, and neither can the amplified output of a vacuum tube.
If a tube light that offers a total resistance of 1 kilo ohms is connected to power supply how much current will it consume?
ANSWERS; Transparent
History of power supply?
The first power supply was created in the 1920s, as devices used for powering residential and commercial radios. Many changes have occurred over the decades from using vacuum tube linear regulators, to the use of semiconductors, and eventually fault tolerant devices.
What are the 4 parts of a cathode ray tube?
four parts of CRO: 1-crt 2-horizontal section 3-vertical section 4-power supply
What has the author Colleen A Switzer written?
Colleen A. Switzer has written: 'Coaxial tube array space transmission line characterization' -- subject(s): Space stations, Power supply
What is the function of a DC power supply?
By Khalid BetaniDirect current (DC) is the unidirectional flow of electric charge. Direct current is produced by sources such as batteries, thermocouples, solar cells, and commutator-type electric machines of the dynamo type.So the function of a DC Power Supply is to provide Direct current to various accessories of computer such as Hard Disk, Ram, Picture Tube or LCD, Mother Board, CD Rom/DVD Rom, etc, so that they function properly.
Block diagram of computer monitor?
chroma circuit, luminance circuit, picture tube, vertical and horizontal circuits, sync circuit, high voltage circuit, low voltage power supply
Why is the capacitor used in tube light?
Starters in tube light uses capacitors to produce a momentary high voltage of 400V due to discharging of capacitor. This momentary high voltage will start the gaseous discharge to priduce light by initial flickering . now,if capacitor is not used , the power supply from the main cannot start the gaseous discharge .
What is the output voltage of eht which go to a CRT?
A large positive charge at the face plate of a CRT; in the order of 14,000 to 31,000 volts, is necessary to attract the electron beam from the neck of the picture tube to the front surface of the tube. There is a separate power supply in most CRT based viewing devices that supply this voltage. Large CRT's usually require higher voltages. High light outputs on any CRT requires more power from the high voltage supply than low light outputs. High voltage is also known as Extremely High Tension, EHT. VE T11.
How do you decide the speed of the tattoo machine?
Each artist finds and performs different settings for their personal machine, allowing the artist to feel comfortable using the machine. The type of skin the client has, along with the size or type of tattoo, determines the setting of the machine and the power supply. Plug in the power supply and attach the cord to the tattoo machine. Place the tube in the tattoo machine and insert the needle in the tube. Tap the foot pedal to ensure the machine is working. Adjust the springs on the tattoo machine to control the depth. Apply pressure with the hand that holds the machine, pressing down into the skin for more depth after adjusting the springs. Turn the voltage of the power supply up to adjust the speed. The more voltage, or higher setting, of the power supply equals a quicker speed. A lower speed is optimal for tattooing bony areas of the body and high speeds for fleshy parts.
Who is the brand power model?
Stacey Engelhart. Type Brand Power on You Tube.
