0
Can you wire a external and an internal ground together on a drier?
Wiki User
∙ 12y ago
The ground wire should go from the dryer directly back to the distribution panel. An external ground wire is not required. The ground wire that is in the cord set that is connected to the frame of the dryer and the ground wire that is in the feeders coming from the distribution panel, that is connected to the ground terminal in the dryer receptacle, is all that is required to satisfy the code requirement.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
How do you properly ground an electric fence?
You need to have a grounding rod made of galvanized steel that is driven straight into the ground until only half an inch of bar is remaining above ground. The ground rod should be at least 6 feet in length. Drier land areas normally require a longer grounding rod, or more of them, spaced 10 feet apart. The ground rods themselves should be placed in [an] area[s] that are naturally permanently moist to have any effect. Then you have to run a grounding cable that is attached to the ground rod along the bottom or top of the fence (can be the top wire or bottom wire) all the way to the fence charger. This cable needs to be attached to the ground rod by ground rod clamps That grounding cable should be attached to that fence charger in order for the fence to be properly grounded. Check out the following links on tips and instructions on how to properly ground an electric fence.
Rate at which electrical energy is converted to another type of energy?
The rate at which an appliance takes energy from the electrical outlet and spinsthe electric meter is the "power" shown on the data label, usually on the backor the bottom of the appliance.The rate at which it actually converts the energy into the form required to do itsjob is also a "power" figure. This one is always less than the power taken fromthe wall outlet, and is not always stated or marked on the appliance.A couple of cases where it is clearly stated:-- Microwave Oven: " 600 Watts of Cooking Power "The microwave oven is using perhaps 1,500 to 2,000 watts from the electric company,converting some of it into radio waves (with less than 100% efficiency), and delivering600 watts of microwave radiation to the cooking chamber.-- Blow Drier: " 1,250 Watts of Drying Power "The blow drier is using perhaps 1,500 watts from the electric company, anddelivering useful energy at the rate of 1,250 watts, in form of a hot coil anda strong little fan motor to blow air across the coil.But on an electric stove, furnace, blender, food processor, fan, telephone, TV,computer, vacuum, washer, dryer, etc., you can find the power consumptionmarked somewhere on it, but it's not clear exactly where that power goes.
What problems are caused by static electricity and what are the solutions?
Many people have static problems, especially in the winter when the indoor air is very dry. But don't worry, static elimination may be easier than you think. There are many steps you can take to eliminate static electricity, and many static control products available. Static Elimination Tips Our expert in static electricity in the electronics industry suggests trying the following to get rid of static electricity problems in your home or office: 1) Increase the humidity in your house and workplace. Air is much drier in the winter, which increases the frequency and severity of shocks. Use a humidifier. 2) Change clothes - switch to natural fibres, since synthetics pick up more of a static charge. 3) Change shoes - there are special conductive shoes in a variety of styles. They are made for people working in the electronics industry. You will need to find a store or catalogue that sells or can order them for you. (Search on line for "esd shoes") 4) If your skin is very dry - try an anti-static hand lotion (also available for the electronics industry.) Here are 3 more suggestions for static control from other sources: 1) Walk barefoot. (Or, as silly as it may sound, cover your shoes with aluminium foil when possible) to reduce the static build up. 2) Wear a thimble on your finger, or carry a coin, and use them to touch grounded metal objects as often as possible. This will not eliminate the static discharge, but will stop the pain you feel in your fingertips. 3) Be sure to ground yourself before touching sensitive electronic equipment.
What are some of the applications of shunt motors?
1. D.C Shunt Motors:It is a constant speed motor.Where the speed is required to remain almost constant from noload to full load.Where the load has to be driven at a number of speeds and any one of which is nearly constant. Industrial use: Lathes Drills Boring mills Shapers Spinning and Weaving machines. 2. D.CSeries motor: It is a variable speed motor.The speed is low at high torque.At light or no load ,the motor speed attains dangerously high speed.The motor has a high starting torque.(elevators,electric traction) Industrial Uses: Electric traction Cranes Elevators Air compressor Vacuum cleaner Hair drier Sewing machine 3. D.C Compound motor: Differential compound motors are rarely used because of its poor torque characteristics. Industrial uses: PressesShears Reciprocating machine.
Why do you get electrical shock when switch is off?
Have you ever been "shocked" when you touched a doorknob, a car-door handle, or a water fountain? Ouch! Well, then you already know something about the effects of static electricity. A Shocking Atom What you might not know is how static electricity happens. It all starts with a tiny thing called an atom. Everything in the world is made up of atoms - from your pencil to your nose. An atom is so small you can't see it with your eyes - you'd need a special microscope. Think of atoms as building blocks for all the stuff in the world. Each tiny atom is made up of even tinier things: protons, which have a positive charge electrons, which have a negative charge neutrons, which have no charge Most of the time, atoms have the same number of protons and electrons and the atom charge is neutral (not positive or negative). Static electricity is created when positive and negative charges aren't balanced. Protons and neutrons don't move around much, but electrons love to jump all over the place! When an object (or person) has extra electrons, it has a negative charge. Things with opposite charges are always attracted to each other, so positive charges seek negative ones and negative ones seek positives. If you scuff your feet on your living room rug, you pick up extra electrons and have a negative charge. Electrons move more easily through certain materials like metal, which scientists call conductors. When you touch a doorknob (or something else made of metal), which has a positive charge with few electrons, the extra electrons want to jump from you to the knob. That tiny shock you feel is a result of the quick movement of these electrons. You can think of a shock as a river of millions of electrons flying through the air. Static electricity happens more often during the colder seasons because the air is usually drier, and it's easier to build up electrons on the skin's surface. So, the next time you get a little shock from touching a doorknob, you'll know that it's just electrons jumping around.
Why is there condensation on your AC accumulator drier?
because its colder than the external temperatue there fore it condensates
What would drier air cause a raindrop to do?
Evaporate before it reaches the ground, potentially.
Does the midwest's climate get wetter or drier as you move from east to west?
drier
Why do salt crystal grow mostly occurs in drier regions?
Because there is less amount of rainfall and temperature that could combine together to accelerate weathering process in drier regions. Therefore, thawing and freezing that could occur there lead to crystallization of salt.
Which is the drier continent- Australia or Antarctica?
Antarctica is drier than Australia.
What is drier the Moon or the Gobi desert?
moon is drier by a factor of 1000
Which is drier the Sahara Desert or the Namibia Desert?
The Namib desert is drier.
When you replace a receiver-drier what should you do with the old receiver drier?
Trash it.
When was Moosie Drier born?
Moosie Drier was born on August 6, 1964.
What is Moosie Drier's birthday?
Moosie Drier was born on August 6, 1964.
What region is drier west or northwest?
The Northwest is drier than the West.
When water vapor changes into a liquid will the air gets drier or wetter?
drier couse when we have vapor air is wet and when we lost it makes air drier.
