0
Your amp should have connections labelled as "high level" or "speaker level" inputs, or something to that effect. If it does, then you simply run the speaker wires to these connections, then run the outputs to the speakers. (obviously you still need to wire the power, ground and remote turn-on to actually power up the amp)
What else can I help you with?
What is the recommended impedance for connecting a guitar amplifier head to a 16 ohm cab?
The recommended impedance for connecting a guitar amplifier head to a 16 ohm cab is also 16 ohms.
How do you do bypass on a factory amp on a Lexus es 300?
To bypass the factory amplifier in a Lexus ES 300, first, locate the amplifier, usually found in the trunk or behind the rear seat. Disconnect the wiring harness from the factory amp, and then connect the speaker wires directly to the head unit or an aftermarket amplifier, ensuring proper polarity. Additionally, you may need to use a line output converter if you're connecting to an aftermarket head unit without speaker outputs. Always refer to a wiring diagram for your specific model year to ensure accuracy.
Can you bypass the factory amp in a Jeep Cherokee?
Yes, you can bypass the factory amplifier in a Jeep Cherokee by using a bypass harness or by directly connecting the head unit's output wires to the speakers. This involves disconnecting the factory amp and routing the audio signals from the new head unit directly to the speakers. However, it's important to ensure the wiring is done correctly to avoid damaging the audio system. Always consult the vehicle's wiring diagram or seek professional installation if unsure.
Where can you find a diagram for a 95' Lincoln Continental factory stareo system?
If you are trying to put in a new stereo I have your answer. The 96 continental that i have ( i am assuming that yours being a year older is the same) came with a factory amplifier. Thus, the stereo head unit is wired directly this amplifier ( unlike standard stereos which have speakers directly wired to the head unit. This amplifier is located in the trunk, you must remove the top panel in the trunk closest to the back seats to acess it. From the amplifier the wires run to the four door panel speakers. Once you acess this amplifier you can proceed with any modifications that you wish to make. mkelly12@ramapo.edu
What are the key features to consider when choosing a guitar amplifier head for optimal performance?
When choosing a guitar amplifier head for optimal performance, consider the wattage for volume, the number of channels for versatility, the type of tubes or transistors for tone, the effects loop for adding effects, and the speaker output options for connecting to different cabinets.
Where is the audio amplifier in 2002 Nissan Sentra?
if the car is not equiped with a factory amp then it is on the radio head unit itself. if it did most nissan's have it behind one of the rear panels in the trunk.
Where is the factory amp located on a 2002 GMC Yukon XL?
On a 2002 GMC Yukon XL, the factory amplifier is located inside the center console, beneath the cup holders. The cup holders can be detached by popping them out with a flat head screwdriver.
Does a 2001 Celica have an amplifier already installed?
The 2001 Toyota Celica typically comes with a standard audio system that does not include a separate amplifier. Instead, it relies on the head unit and factory speakers for sound amplification. However, some higher trim levels or optional audio packages may offer better sound quality but still do not feature a standalone amplifier. If you're looking for enhanced audio performance, you may need to install an aftermarket amplifier.
Where is the factory stereo amplifier for 97 ford e-series van?
inside the front passenger side kick-plate (just in front of the fuel reset switch)... three little metric head bolts hold it in.
What is an amplifier head and how does it contribute to the overall sound of an electric guitar?
An amplifier head is the main component of an amplifier that controls the tone and volume of an electric guitar. It amplifies the signal from the guitar pickups and shapes the sound through various controls like EQ and gain. The amplifier head significantly influences the overall sound of the electric guitar by boosting the signal and adding coloration or distortion to create different tones.
What are Pre-Amp outputs?
They are RCA type connectors on the back of your Head Unit (Radio). There are 2 connections, usually blue and white, the cord for this has the same connectors on both ends. The Pre-Amp outputs are a direct line for the Signal from your Head Unit to go directly to an Amplifier (you will see similar connections on your Amplifier as you see on the back of your Head Unit), so when you run speaker wire from your Amplifier, the speakers will play the sound (Music) your Head Unit is producing no matter if its from the CD or FM/AM tuner or AUX input like from an I-Pod.Another AnswerA pre-amplifier, which is also known as a 'control unit', a high-fidelity unit which is separate from, but which must be used together with, a 'power amplifier'.Pre-amplifier/power amplifier units are normally regarded as 'high end' equipment and tend to be very expensive. The pre-amplifier unit is equipped with inputs for phono, CD-player, tuner, and various other auxiliary units and (usually) provides a single pair (right- and left-channels) audio outputs for connection to the power amplifier. The pre-amplifier is the unit which provides the volume control, tone controls, filters, etc., while the power amplifier simply amplifies the output from the pre-amplifier unit. The output usually takes the form of a pair of RCA connectors, usually colour coded white and red.Some 'home theatre' amplifiers provide a 'pre-amplifier' output, which bypasses its internal power amplifier, for the purpose of adding external power amplifiers, if desired.
What are the difference of series and parallel?
series means connecting tail of one to head of another oneparallel means connecting tail of all and head of all
