0
Repairing a crankshaft position sensor would be difficult if not impossible depending on what is wrong with it. They are relatively inexpensive so replacing it is the best option.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
Where is the crankshaft position sensor located on a 97 Honda Accord 2.2 non v tech and how do you replace it?
This would be located right behind the crankshaft. For the best assistance, you can use the users manual to get it fixed.
Where is the location of the crankshaft position sensor for a 1997 Mitsubishi Montero Sport LS 3.0L eng?
Look for the crankshaft position sensor right next to the timing belt pulley at the driver's side of the crankshaft where it exits the front of the block. It is located inside the lower front timing cover and is mounted onto the block itself.It is a LOT of work to get the engine torn down far enough to access it. You may want to test it/have it tested before digging in that deep as they rarely fail.By the way, they mount in a fixed position which is NOT adjustable (IE you cannot advance the timing by moving it around etc).Good luck
Where is the camshaft position sensor on a 1993 4.0 L Grand Cherokee LTD?
On the top of the bell housing. thats the crank position sensor the cam sensor in a 93 is fixed in the distributor to replace it you need a new distributor
On a 1994 ford ranger the crank position sensor it brakes the magnet off the sensor and there is not enough adjustment to stop it how can you stop that?
On a 4.0 V-6 the crank position sensor is in a fixed location and cannot come in contact with the crank if it is installed correctly.
My EPC light came on my Audi A3 and sometime the car will not start why?
The crankshaft positon sensor is wrong. I replaced it on my 2001 A4 fixed the problem.
What could be wrong if a 1996 Buick LeSabre starts and drives then will not start again?
I had the same problem with a 1992 Park Avenue with the 3800 engine. I first replaced the electronic ignition but that did not fix the problem. I then replaced the crankshaft heat sensor. That fixed my problem.
P0342 camshaft position sensor circuit low input how can you fix on 1998 Isuzu amigo 4 cylinder and where is lacated?
How fixed camshaft sensor circuit low input
Why does a 1987 Chevy Celebrity start up and run for about 10 minutes and then die and wont start for about another 10 minutes and then die again?
I had a similar experience with my 1987 Chevy Celebrity. In my car's case I replaced the ignition module and the crankshaft position sensor. Between the two the problem seems to be fixed.
What sort of sensors go bad in a Dodge truck?
The sensors that usually go bad in a Dodge truck are the throttle position sensor, the oxygen sensor, engine light sensor and crank sensor. These malfunctions can be fixed on any Dodge dealership.
Why does your 91 Jeep Cherokee bog out when you step on the gas?
I am having the same problem with my 93 jeep cherokee. it can hardly get out of its own way! i just recently rebuilt my motor and transmission. i replaced the cps ( crankshaft position sensor) and it made a noticeable difference, but still hasn't fixed the problem completely! I need help!
If you replaced the crankshaft sensor on a 1996 Chevy Cavalier would the 'check engine light' go off if that was the only problem?
light should go off . if that was the problem, and is now fixed, disconnect the battery for 5 minutes,then reconnect battery this will reset the computer and remove the signal from the warning light if that doesnt work, there is a different problem apart from crankshaft sensor
Can a crankshaft on an alfa 166 be fixed?
Well crankshaft on alfa's 166 like mine can not be fixed if you have excessive wear or scoring on journals...That is because they are nitred...If your crank is damaged you need new one
