Label and identify the parts of a microscope?

Answer 1

(Easier point view notes below)

Eyepiece Lens: the lens at the top that you look through. They are usually 10X or 15X power.

Tube: Connects the eyepiece to the objective lenses

Arm: Supports the tube and connects it to the base

Base: The bottom of the microscope, used for support

Illuminator: A steady light source (110 volts) used in place of a mirror. If your microscope has a mirror, it is used to reflect light from an external light source up through the bottom of the stage.

Stage: The flat platform where you place your slides. Stage clips hold the slides in place. If your microscope has a mechanical stage, you will be able to move the slide around by turning two knobs. One moves it left and right, the other moves it up and down.

Revolving Nosepiece or Turret: This is the part that holds two or more objective lenses and can be rotated to easily change power.

Objective Lenses: Usually you will find 3 or 4 objective lenses on a microscope. They almost always consist of 4X, 10X, 40X and 100X powers. When coupled with a 10X (most common) eyepiece lens, we get total magnifications of 40X (4X times 10X), 100X , 400X and 1000X. To have good resolution at 1000X, you will need a relatively sophisticated microscope with an Abbe condenser. The shortest lens is the lowest power, the longest one is the lens with the greatest power. Lenses are color coded and if built to DIN standards are interchangeable between microscopes. The high power objective lenses are retractable (i.e. 40XR). This means that if they hit a slide, the end of the lens will push in (spring loaded) thereby protecting the lens and the slide. All quality microscopes have achromatic, parcentered, parfocal lenses.

Rack Stop: This is an adjustment that determines how close the objective lens can get to the slide. It is set at the factory and keeps students from cranking the high power objective lens down into the slide and breaking things. You would only need to adjust this if you were using very thin slides and you weren't able to focus on the specimen at high power. (Tip: If you are using thin slides and can't focus, rather than adjust the rack stop, place a clear glass slide under the original slide to raise it a bit higher)

Condenser Lens: The purpose of the condenser lens is to focus the light onto the specimen. Condenser lenses are most useful at the highest powers (400X and above). Microscopes with in stage condenser lenses render a sharper image than those with no lens (at 400X). If your microscope has a maximum power of 400X, you will get the maximum benefit by using a condenser lenses rated at 0.65 NA or greater. 0.65 NA condenser lenses may be mounted in the stage and work quite well. A big advantage to a stage mounted lens is that there is one less focusing item to deal with. If you go to 1000X then you should have a focusable condenser lens with an N.A. of 1.25 or greater. Most 1000X microscopes use 1.25 Abbe condenser lens systems. The Abbe condenser lens can be moved up and down. It is set very close to the slide at 1000X and moved further away at the lower powers.

OR IN EASIER WORDS:

Eyepiece -part you look through

- magnifies 10x

-magnifying power engraved side of eyepiece

Tube -holds eyepiece

-holds objective lenses at proper distance

Coarse-adjustment knob -moves stage up or down to focus

-only used with low-power lens

Fine-adjustment knob - use with medium and high-power magnification

-use to bring sharper focus

Arm - connects the base and tube

- use to carry the microscope

Revolving nosepiece - disk holds 2 or more lenses

- turn to change lenses (clicks in place)

Objective lenses - Magnifies the object

- Each lens has different power magnification (10x, 40x, 100x) power engraved on side of lens

- be sure you can identify lens (low- power lens = 10x)

Stage - supports slide (holds in position)

- hole in centre of stage (allows light source light to pass through)

Condenser lens - Directs light to object being viewed

Diaphragm - Controls amount of light reaching object being viewed

Light source - shining light through object being

viewed (makes easier to see)

Answer 2

eye piece lens: is a type of lens that is attached to a variety of optical devices such as telescopes and microscopes.

tube: connects the eyepiece to the objective lenses.

arm: supports the tube and connects it to the base

stage:the platform whre you place your slides.

revolving nosepiece or turret"this is the part that holds two or more objectives lenses and can be rotated to easily change power.

diaphragm or iris: manny microscopes have a rotating disk under the stage . this is diaphragm has different sized holesa and its used to vary the intensity and size of the cone of light that is projected upward into tha slide.

condenser lens:the purpose of the condenser lens is to focus the light onto the specimen.

Answer 3

There are the:

eye pieces

clamp

top light

on/off switch

stage

stage clamps

base

diopter adjustment knob

magnifying glass

brightness adjustment knob

Answer 4

I don't have a diagram but... the OCULAR/EYEPIECE (where you look through) the ARM (holds the things together) the STAGE (where you put the thing you want to magnify) the STAGE CLIPS (hold stage in place) the REVOLVING NOSEPIECE (which holds the objectives) the OBJECTIVE LENSES (3 things that help you magnify more or less) the DIAPHRAGM (don't care about spelling) changes the amount of light coming through) the LIGHT (i hope you know what that is) the BASE (bottom of the whole thing)

Answer 5

The main parts of a microscope are the eyepiece, objective lens, stage, arm, coarse focus knob, fine focus knob, base, illuminator, and condenser. The eyepiece is where you look through, the objective lens magnifies the specimen, the stage holds the specimen, the arm supports the upper parts, the focus knobs adjust the focus, the base supports the microscope, the illuminator provides light, and the condenser focuses the light onto the specimen.

Answer 6

yes