0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is the difference between signal processing and signal conditioning?
processing is nothing
What is the difference between the modulating signal and the demodulating signal in output of the detector?
Distortion.
Difference between analog and digital control systems?
An analog control system is one that presents data by measuring a continuous variable. This reports the data back in voltage or pressure.
What is the difference between signal and event?
The main different between a traditional signal and a message is their recipient. A signal is often sent to a mass of people, while a message is more individualized.
What is phase difference?
A phase difference between two periodic signals is the time difference between two corresponding points on each signal. This time difference is usually measured in degrees or radians, but can be given as a unit of time as well.
Difference between strobe and handshake signal?
A strobe signal is sent by the signal sender without any regard to the signal receiver. This assumes that the design provides sufficient setup and hold time, along with transmission time, to ensure reliable receipt of the signal. A handshake signal is a bi-directional protocol between the signal sender and the signal receiver, which the receiver uses to tell the sender that the signal has been received. In this system, it often does not matter what the transmission time is, but bandwidth can be reduced since the sender must wait for the handshake to come back from the receiver, effectively doubling the time it takes to send a signal.
What is difference between vga and lcd display?
The main difference between the tow is the signal. VGA uses an analog signal and DVI is a digital signal.
What is the difference between signal processing and signal conditioning?
processing is nothing
What is the difference between signal and wave?
wave is a part of a signal . millions of wave construct a signal .
What is the difference between the modulating signal and the demodulating signal in output of the detector?
Distortion.
What is the difference between a valve and actuator?
actuator is a mechanism that will responds to hydraulic,pneumatic and electrical signal ,it is used to control the valve that to be in open or close condition.
What do you mean single and double handshaking of microprocessor 8086?
They are the ways of transmitting parallel data to the microprocessor. In single handshake, a peripheral device first sends a "Strobe signal" to the microprocessor to indicate that it is ready to send data. The microprocessor , upon detecting the strobe signal, opens up its input port and receives the data. After receiving data, it sends an "Acknowledge signal" to the peripheral to indicate that transmission has been completed.A transmission session has been completed. In double handshake, first the peripheral device sends a strobe signal, the microprocessor, sends the acknowledge signal to indicate that it is ready to receive data. After which data is received.After sending data, the peripheral sends a strobe signal to indicate data transmission completion, due to which, the microprocessor drops its acknowledge signal and a session has been completed. The only difference in the two is that, in double handshake, the peripheral is informed about the microprocessor's readiness to receive data. This is doesn't happen in single handshake. So the name follows "double handshake", literally meaning "double confirmation".
What is the difference between analog and digital modulation Does it depends on baseband signal?
The basic difference is that in analog modulation the modulating signal is analog signal and in digital modulation it is in digital form.
What is the difference between information and signal?
Information refers to data that has been processed and organized to convey meaning or knowledge, while a signal is a physical representation of information that is transmitted through a medium such as sound waves or electrical pulses. In other words, information is the content being communicated, while a signal is the form in which that information is transmitted.
What is the difference between SINR and CINR?
SINR - Signal to Interference and Noise Ratio CINR - Carrier to Interference and Noise Ratio difference between those to is difference between carrier and signal carrier is signal who doesn't "carry" any information . it must be modulated( by phase,freq or amplitude) and those changes convey information. carrier is unmodulated signal signal is defined as useful signal which carries information SINR is power of signal to power of interfenence and noise ratio
What is the difference between primary and secondary transducers?
the difference between both are: Primary transducer:The Mechanical device which converts physical quantity to be measured into a mechanical signal. Secondary tranducer:The Electrical device which converts this mechanical signal to the electrical signal.
What is the difference between a wave and signal?
1.wave is a three dimensional object where as signal is a two dimensional object
