Want this question answered?
How does a fixed bore expansion device respond to a reduction in load?
The higher the mismatch between the load impedance and source impedance, the higher the loading effect.
when load on the electric system increase frequency of the system will decrease resulting in higher intake at powergenerators. If higher intake is not net by powergeneration stations entire power system will collapse. It is called grid failure.Another AnswerAn increase in load will result in an increase in load current.
Because a transformer is a big lump of metal that takes time heat up, so if the load is on and off in a short time, the load rating can be exceeded.
An open circuit or a short-circuit (if that circuit is complete).
How does a fixed bore expansion device respond to a reduction in load?
Milk is pasteurized which reduces the microbial load. That makes it last longer.
The stress reduction factor is a product of the relationship between the Unconfined compressive strength of a rock and the sigma 1, or principal stress field in that area. The higher the value, the more likely the rock is to deform when placed under load.
under the dashboard..
Reduction of transient load and lightining strikes
Generally the capacitor rating of a bank are decided on the load factor.ie higher the KVAR higher the capacity.KVAR is the reactive power in which load angle differs with the load variation.If we know load factor multiply it by the sine angle which gives us the capacity of the cpapcity of the load bank. Generally the capacitor rating of a bank are decided on the load factor.ie higher the KVAR higher the capacity.KVAR is the reactive power in which load angle differs with the load variation.If we know load factor multiply it by the sine angle which gives us the capacity of the cpapcity of the load bank. Generally the capacitor rating of a bank are decided on the load factor.ie higher the KVAR higher the capacity.KVAR is the reactive power in which load angle differs with the load variation.If we know load factor multiply it by the sine angle which gives us the capacity of the cpapcity of the load bank.
An overload occurs when the load current is higher than the nominal current rating of the conductor supplying the load. Over time, this can cause the insulation to break down and cause a short-circuit to occur between conductors.
Microbial load (cfu/g or cfu/ml) can be expressed as log10. So, if you have 100,000 microbes that is 5 log, 10,000 microbes is 4 log, 1,000 is 3 log, 100 microbes is 2 log and 10 microbes is 1 log. Now, if you went from 100,000 microbes cfu/g to 10,000 microbes cfu/g that would be a 1 log reduction (5 - 4 log). If you went from 100,000 to 32,000 that would be a 0.5 log reduction (5 - 4.5 log) and so on. I hope this helps St John Hall
The higher the mismatch between the load impedance and source impedance, the higher the loading effect.
Short is short (no pun intended) for short circuit, which is a condition where unexpected current flows, often of much higher current than usual, because the load is often bypassed. Short circuit current flow can be as high as several hundred or several thousand amperes. Some people make the mistake of saying "there is a short" when they actually mean "there is an open". This comes from an intermittent connection that causes the load to not function. If there were a true short, there would be a big spark, possible fire, and the fuse or circuit breaker would blow.
The relationship is linear. Nothing more can be said without more information in the question.
No. No load and short circuit is not similar. No load can be 1) Either open circuit i.e. Only Potential is available and load is not connected 2) Load (i.e. motor etc ) is connected but not working with full load or full capacity. In this case the current will flow through the circuit depending on the load. It means No load condition is a condition where no current or a small ( relative / comparative term) current is flowing through the circuit. In Short circuit the load side resistance/ impedance become so less that very high amount of current is passing through circuit.( The protection is therefor required for any circuit) No load and and short circuit is not similar. Thanks