0
Do exhaust manifolds from a 1964 Galaxie 390 fit a 1964 Galaxie 352 motor?
Wiki User
∙ 14y ago
Yes, almost every part for the big block fords are interchangable (with the exception of the crank and pistons of course).
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Will a 1967 289 fit into a 1964 falcon?
Yes. The only issue you may have is the exhaust manifolds. The Falcon has a little less clearance between the shock towers that the mustang. You may need to find some V8 falcon exhaust manifolds or purchase some aftermarket headers.
How long is a 1964 ford galaxie?
18 ft
Which is the power of the engine and the maximum speed of the ford galaxie automatic 1964?
145.5 kW / 195 hp is the power of the ford galaxie automatic 1964 engine and its maximum speed is 135 mph.
Which side of the deck-lid does the jack instruction decal go on a 1964 Ford Galaxie 500 Convertible?
On my 1963 Galaxie 500 it is on the right side
How many 1964 ford galaxie 500 XL convertable were produce by ford?
15,169 total 1964 Galaxy convertible production.
What does the fuse box look like on a 1964 Ford Galaxie look like?
The fuse box on a 1964 Ford Galaxie looks like a small gray box with a removable cover. The fuse box is located on the front panel just to the left of the driver's seat.
What engines were the Chevrolet iron rams horn exhaust manifolds used on?
Used on 1955, 56, and 1957 Chevy small block V8.Applications for these manifolds include, but are not limited to:1955 & up SB Chevy 283 305 350 V8 engine.1958 - 1964 full size Chevrolet (Impala, Bel Air etc)1962 - 1965 Corvette.
Did Ford offer a swing away steering in 1964 Galaxie 500 XL?
Yes it was an option. The swing away steering wheel is a rare option for a Galaxie that cost around $26.10 when ordered. Yes you could find it in the XL model as well as the 500 model even in a Galaxie wagon. This option was more common in the thunderbirds
How many 1964 galaxie 500 XL Convertibles were produced with the swing away steering wheel?
There were 15,169 Galaxie 500 XL convertibles produced in 1964. The swing away steering wheel was an option on all but the Thunderbird where it was standard after 1962. There were very few 500 XLs sold with this option but it could be ordered on any Galaxie from 1963 to 1966. As to the exact number of 500 XL convertibles equipped with this option I have been unable to find that information.
Where is the fuel pump on a 1964 Lincoln Continental?
On a 1964 Lincoln it should be attached to the engine on the drivers side underneath the exhaust manifold.
What are the manifold bolt torque spec for gm 292 engine?
I have an official 1963 Chevrolet Truck Shop Manual, published in 1962 by GM. I also have the Supplement Truck Manuals for 1964 and 1966, which are meant to be used with the 1963 Manual and cover changes made in those years. 1963 apparently was the first year of the 6 cylinder 230 and 292 engines, which continued for 1964. In 1966 the inline 6 cylinder engines included the 230, 250, and 292. The intake and exhaust manifolds are both mounted on the left (driver's side) of the engine and are bolted together as a unit. The 1963 Manual reads on page 6-19, "IF NECESSARY to replace either intake or exhaust manifold, separate them by removing 1 attaching bolt and 2 nuts at center of assembly. Reassemble manifolds using new gasket. Tighten finger tight and torque [joining bolt/nuts] [to] 15-30 ft lbs AFTER assembly to cylinder head." Page 6-19 of the 1963 Manual also shows a photograph of the manifolds' side (left side) of the straight 6 motor. There are positioning pins threaded into the engine block that insert into holes at both ends of the manifolds assembly. These are not bolts, but are pins. Between the ends of the manifolds assembly, there are 6 bolts, each with a spanner piece to clamp the manifolds to the engine. The longer, outer (front and rear) 2 bolts (with longer clamps) are torqued to 15-20 ft pounds. The shorter 4 bolts (with shorter clamps) that are spaced along the center of the manifolds assembly are torqued to 25-30 ft pounds. In the 1964 Supplement Manual, the manifold torques are not mentioned, so I assume are unchanged from 1963. In the 1966 Supplement Manual, the manifold torques are listed as 20 ft lbs outer bolt clamps, and 30 ft lbs all others.
What was the original tire size of a 1964 ford galaxie?
750-14 is the OEM size. This converts to these modern sizes. 205/75-14 215/70-14 235/60-14
