0
What else can I help you with?
What is the process for performing a vacuum breaker replacement?
To perform a vacuum breaker replacement, follow these steps: Shut off the water supply to the vacuum breaker. Remove the old vacuum breaker by unscrewing it from the pipe. Clean the area where the old vacuum breaker was attached. Install the new vacuum breaker by screwing it onto the pipe. Turn the water supply back on and test the new vacuum breaker for leaks. Remember to follow any specific instructions provided by the manufacturer for your particular vacuum breaker model.
Installed new carburetor n now wont shift?
Vacuum lines installed correctly? Vacuum ports on carb. working?
How expensive is it to have a central vacuum system installed in the home?
A central vacuum system installed in a home can range in cost from four hundred dollars to five thousand dollars. These systems can be installed in a new or previous built home.
Stainless Steel Sink?
form_title= Stainless Steel Sink form_header= Install a stainless steel sink for a new look in your home! Where do you want the sink installed?*= _ [50] Do you want a to install a double sink?*= () Yes () No () Not Sure What is your budget for the sink?*= _ [50]
What can you do if a new faucet was recently installed in the kitchen and the drain vent next to the faucet shoots like a geyser when the dishwasher is turned on?
My guess is your garbage disposer was also replaced and they forgot to knock out the plug before connecting the disposer hose/drain It sounds like you have a vacuum breaker on the drain for the dish washer. This is probably just a coincidence but your vacuum breaker needs to be replaced or repaired. It really has nothing to do with the faucet installation.
Can a vessel sink be installed where a existing undermount sink is?
Yes, a vessel sink can be installed in place of an existing undermount sink, but it may require modifications to the countertop and plumbing. The cutout for the vessel sink needs to be appropriate for its design, and the height of the sink will differ, potentially affecting the faucet placement. Additionally, ensure that the new sink's drain aligns with the existing plumbing. It's advisable to consult a professional for the best installation approach.
Vessel Sinks?
form_title= Vessel Sinks form_header= Install a vessel sink in your home. What size sink do you want installed? *= _ [50] Will you be redoing your entire bathroom?*= () Yes () No What is your budget for a new sink?*= _ [50]
How do you replace vacuum breaker of my geyser?
Switch off incomong water, screw old device out, then new one in, switch on again
How do I properly install a new breaker in my electrical panel?
To properly install a new breaker in your electrical panel, follow these steps: Turn off the main power supply to the panel. Remove the panel cover to access the breakers. Identify the slot where the new breaker will be installed. Insert the new breaker into the slot, making sure it is securely in place. Connect the wires to the breaker according to the manufacturer's instructions. Replace the panel cover and turn the main power supply back on. It is recommended to consult a licensed electrician if you are unsure about any step in the installation process.
What do I need to buy to install a shampoo sink at home?
A new sink with a spray device like a small handheld shower, a new drain extension and a water supply. Best near an existing sink or bath. -I have installed quite a few of these for home hairdressers. About 5-6 hours labour depending on existing setup.
What could be wrong if you installed a new sink in the basement and there is no hot water pressure in the house?
One of the valves that you closed while hooking up the hot water to the sink was probably an old gate valve... It broke and did not fully re-open.
Can you run an extra set of wires off a 20 amp breaker?
No, this is stated very clearly in the electrical code. Only one branch circuit is to be allowed connected to each individual circuit breaker no matter what the amperage is. If a new branch circuit is installed and there are no spare breakers then most distribution panels have the ability to let tandem breaker be installed in it. Tandem breakers have two terminals and two handles and have the ability to fit into a single slot in the distribution panel.
