0
Do you have to remove the toilet tank to replace the ballcock valve?
Wiki User
∙ 15y ago
No. The instructions for replacing the ballcock valve should be printed on the package for the new valve. You can also discuss it with an employee at a good hardware or home improvement store who should be able to explain and maybe even demonstrate the procedure for you.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How do you fix singing toilet?
Just replace the ballcock valve..
How do you replace a flush valve in a toilet?
Have the new valve in hand. Cut the toilet water supply off at the commode, or even at the street meter box.Remove water tube or pipe supply and old flush valve. Install new valve and new supply line if required.
How do you change a hose bib in the garden?
By isolating the valve then remove it and replace it
How do you replace toilet flush valve?
Take tank off of the bowl and replace it . Always install new tank to bowl bolts and washers and tank to bowl gasket. The flush valve is what your tank ball is conected too. If your talking about ballcock then you just take it out with out having to do the above. The ballcock is what lets the water come into tank. Always shut off water either way. If you cannot get the bolts to come lose you will have to hack saw them off, it will take a little while to do so but it works best. You will only use the blade it self and turn the blade around. And you will be cutting between tank and bowl and put something on the bowl so not to scatch the bowl like duct tape or what ever you have like this. and if you have a brass nut on flush valve under tank you will have to cut it also
How do you replace main water valve?
You turn off the water valve before it -probably on the sidewalk, or just on your front yard. Then remove the main valve and replace it. NOT a job for amateurs. I hope you have some experience at least.
How do you fix singing toilet?
Just replace the ballcock valve..
What if your toilet makes a noise out of no were?
Your ballcock is comming on -- replace tank ball or sometimes you have to change out flush valve -- but change tank ball first and see if that will do it You hardly ever have to change flush valve -- Your ballcock is what lets water come into your tank
What should you do if your downstairs bathroom continues to run after the toilet is flushed and turning the valve off did not work?
check your pressure regulator valve or house pressure .Replace fixture stop and ballcock assy also r&r flapper
Why Overflow pipe leaking?
An overflow pipe on a (toilet cistern?) will leak if the rubber disc in the ballcock slide valve needs to be replaced.
Where is a ballcock used?
A ballcock is a ball float on the end of a lever in the water closet of a toilet. As the level of water in the closet rises, so does the floating ballcock. When the water level is high enough, the lever operates a sliding valve and the water coming into the closet is shut off.
Why would a first floor toilet gurgle when a second floor toilet is flushed?
The water in the lower toilet is probably being siphoned out of the tank by the negative pressure caused by flushing the upper toilet. This CAN happen if the water level in the tank of the lower toilet is over the top of the ballcock. If this is the case, the tank water is being siphoned into your drinking water! Replace the ballcock with a Fluidmaster right away. If you have a small white fill valve that sits in the bottom of the tank, get rid of it. These are illegal and WILL siphon under these conditions. If the lower toilet runs AFTER the fill cycle of the upper toilet, it may be that the ballcock seals at a lower pressure, and the pressure spike when the upper toilet shuts off causes it to run a bit until the added water closes the valve a little tighter.
How can you fix a toilet that groans at the end of the flush?
Replace the fill valve (ballcock). The type that uses a diaphragm, like fluidmaster, will shut it off quicker. Reason that occures: vibrations in the pipe from the fill valve when the water flows through the ballcock ( like a whistle does with air), but water makes a deeper sound and sometimes vibrates quite loudly once that starts. If that doesn't fix it, try replacing the supply water valve.
What would cause the ballcock to suddenly pop up out of its fixture and water to sputter in the tank if this happened spontaneously and not during use?
A surge in water pressure can cause this. Also, a defective ballcock would pop off under these conditions. Replace the ballcock and consider installing a pressure reducing valve (PRV) on the incoming water line.
How do you remove concrete from a gas valve?
Your kidding me right; replace the valve.
Which repairs are typically needed when your toilet is running all the time?
Ballcock valve assembly, plunger not seating correctly, or simply an incorrect water level as excess water is spilling needlessly down the overflow pipe.
Which part of a toilet tank assembly is the supply valve for water to the tank?
That is a fill valve and is part of the ballcock system. When someone pulls the lever, that pulls the chain and lifts the flush valve flapper and empties the tank into the bowl. That causes the float to drop, opening the fill valve and allowing water from the supply to enter and refill the tank.
How do you replace the valve lifters on a cavalier?
To replace the valve lifters on a Cavalier, remove the intake manifold, valve covers and rocker arms. Remove the heads of the lifters using needle-nose pliers.
