answersLogoWhite

0

You turn off the water valve before it -probably on the sidewalk, or just on your front yard. Then remove the main valve and replace it. NOT a job for amateurs. I hope you have some experience at least.

User Avatar

Wiki User

13y ago

What else can I help you with?

Continue Learning about Engineering

What to do if Water valve knob won't turn back on?

Isolate it from the water supply then replace the defective valve


What to do if the water pressure in your house is too high?

There is usually a main water valve that comes into the house, locate this valve and turn it down. Installing a pressure reducing valve after water main valve will allow for adjustment of water pressure to proper setting.


How much does it cost to replace a tp valve on a water heater?

I was charged $464.00 and I thought that was a bit rich to replace a T&P Valve today 26/09/11


How do you replace the relief valve on a water heater?

To replace the relief valve on a water heater, first, turn off the power or gas supply and shut off the cold water supply to the heater. Next, drain some water from the tank to relieve pressure, then use a wrench to unscrew the old relief valve from its socket. Install the new valve by threading it into the socket and tightening it securely, then restore the water supply and check for leaks before turning the power or gas back on.


How do you replace electric geyser pressure valve?

To replace an electric geyser pressure valve, first, turn off the power supply and shut off the water supply to the geyser. Next, drain the water from the tank by opening a hot water tap and using a garden hose to drain from the drain valve at the bottom of the geyser. Once drained, disconnect the old pressure valve by unscrewing it from the tank, then install the new valve by tightening it securely. Finally, reconnect the water supply, refill the tank, and restore power to the geyser.

Related Questions

How can I replace the water shut off valve under the bathroom sink?

To replace the water shut off valve under the bathroom sink, first turn off the main water supply. Use a wrench to disconnect the old valve from the water line. Install the new valve by connecting it to the water line and tightening it with a wrench. Turn the main water supply back on to test the new valve.


What steps should I follow to replace the main water shutoff valve in my home?

To replace the main water shutoff valve in your home, follow these steps: Turn off the water supply to your home. Drain any remaining water from the pipes. Locate the main water shutoff valve. Disconnect the old valve from the pipes. Install the new valve in its place. Reconnect the pipes to the new valve. Turn the water supply back on and check for leaks. It is recommended to consult a professional plumber for assistance with this task.


How can I replace the main water valve in my home?

Replacing the main water valve in your home involves turning off the water supply, draining the pipes, removing the old valve, and installing the new one. It is recommended to consult a professional plumber for this task to ensure it is done correctly and safely.


How can I replace the main water shut off valve?

To replace the main water shut off valve, you will need to first locate the valve, typically near where the main water line enters your home. Shut off the water supply to your home before beginning the replacement process. Use a pipe wrench to loosen and remove the old valve, then install the new valve in its place. Make sure to securely tighten the new valve and turn the water supply back on to test for any leaks. If you are unsure or uncomfortable with this process, it is recommended to seek the help of a professional plumber.


Is the water main valve leaking in your home?

No, the water main valve is not leaking in your home.


Is the main water valve leaking in your home?

Is the main water valve in your home leaking?


What should I do if I notice water leaking from the main shut off valve in my home?

If you notice water leaking from the main shut off valve in your home, you should immediately turn off the water supply to prevent further damage. Then, contact a professional plumber to repair or replace the valve as soon as possible.


What is the process for replacing the main water shut off valve in a residential plumbing system?

To replace the main water shut off valve in a residential plumbing system, you will need to first locate the valve, shut off the water supply to the house, drain the pipes, remove the old valve, and install the new valve. Finally, turn the water supply back on and check for any leaks.


What is main feed water stop valve?

It's a valve that regulates the main water pipe.


Why do you have no water pressure after turning on the main valve?

Water not on at street 'city' valve, or other valves--after inside main valve--off.


How can I replace a water main valve?

Replacing a water main valve involves shutting off the water supply, removing the old valve, and installing a new one. It is important to follow safety precautions and use the right tools for the job. If you are unsure, it is recommended to seek professional help to ensure the job is done correctly and safely.


How do I shut off the main water valve in my home?

To shut off the main water valve in your home, locate the valve typically near the water meter or where the main water line enters your house. Turn the valve clockwise to close it and stop the flow of water into your home.