No All you need is a good working vise, 4 inch or better
On my 99 Suburban, the alarm activates when you press the lock button on the remote twice.
Borrowed from silverado answer: Push the set button and with the set light on, press either the scan or seek buttons to change...
Sounds like a u joint, have it checked and done at a shop. Ujoints in chevrolets are glued in and are not a diy project, unless you have a 15 ton press at home. Then by all means press them out and replace them.
turn on ignition switch and press and release the accellerator three times slowly within 5 seconds. turn if switch and recheck. if fails the first try it again.
Press MENU until you get "UNITS" Press ENTER. When ENGLISH shows Press MENU Done
tells you how right in the owners manual What they don't tell you in the manual is how to reset the message if you don't have the DIC. Press the gas pedal to the floor 3 times in 5 seconds with the key "ON" and the engine off.
With the radio off, press the "set" button. Then press the "scan" button to change the hour and the "seek" button to change the minutes. Once the time is correct press the "set" button once more to change the time.
With the key in the "on" position, but the radio off, press the "set" button, then press the scan buttons to change the hour and minutes. When the correct time is reached, press the set button again.
behind the light in the hood. press the clamp gently, take off the cover behind the lamp, and change the fuse...
97 Chevy s10 pickup. Turn the power off on the radio. Press the [set] button, like you would to do your presets. The word set will show on the display. Press the [seek] button to change the hours and the [scan] button to change the minutes. Then press [set] again to save the time.
Press the inject button.
On the bumper there should be a wiper arm. If you then press it down, it should be come off quite easily. Also, it would help to bring the car in to a mechanic.
There are to buttons "up" "down" press and hold the left one to change the hour.Press and the left one to change minutes.
press the set button then while the set light is on press the seek and scan buttons to change the hours and minutes.
Probably because the light is burned out. It is pretty easy to change.
That pulley is a press fit type. There are not any threads. You will need to rent/buy some pullers for that power steering pulley.
It is written in small print on the SIDE of the tire. That is the max press allowed for that brand/make/size of tire. The recommended pressure for the vehicle will be in the owners manual or on the sticker on the drivers door jamb.
Press escape to open the menu. Press settings. Press controls. Click the control you want to change. Press the key you want to change it to.
There is a button at the bottom of the headrest where it goes into the seat press the head rest down as you press in the button and it will release it as you pull up
to press for - to try to get (for example, a change)
There is a Up and Down Arrows becide the audio button, Press the arrows for about 3 seconds it will beep, It will change the Hour and Min.
Press mode key at any time to exit.Press mode, then press adjust to change time zones.TO SET TIME AND DATE:Press and hold alarm on/off for about 5 seconds until hour flashes.Press adjust to change hour.Press alarm on/offto move to minutes. Press adjust to change minutesPress alarm on/offto move to seconds. Press adjust to change secondsPress alarm on/offto move to month. Press adjust to change monthPress alarm on/offto move to date. Press adjust to change datePress alarm on/offto move to day of week. Press adjust to change day of weekPress mode key to save to exit.TO SET ALARM:Press mode to go to alarm screen (AL shows above temp)Hold the alarm on/off button for about 5 seconds and the hour will flash.Press the adjustbutton to change the hour.Press the alarm on/off button again to move to minutePress the adjustbutton to change the minutesPress the mode key to save and exit
easy press menu then go on to books and then press change name
With engine off. Turn key to on. Press accelerator fully three times. This should reset light.
Turn ignition key to "run" (don't start) and press the gas pedal 3 times within 5 seconds.