0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is the purpose of a panhard rod?
The purpose of the Panhard Rod is to take up lateral forces between the axle and body thus removing load from the radius arms.
What study do you need to take and how long is it going to take to become a hairdresser?
You will need to study for three years at secondary school
When you clamp a single core cable carrying about 500A with an aluminum cable clamp do you have to take care of any effects due to Eddy currents and If so what can you do to minimise these effects.?
Assuming the single core cable forms part of a three phase circuit (i.e. you are clamping three single core cables) it is best to install the three cables close togther in what is called "trefoil" formation. This harmonises the Eddy currents of each phase.
What do plants need to take in photosynthesis?
They need light, water, carbon dioxide.
How do you take apart a col-gear shifter 1994 Ford F-150 a diagram would be helpful?
take out the 4 bolts that hold the steeering column,undo the wire to the shift indicator,drop the column down,,undo the two bolts holding the shifter cable,undo the bolt holding the steering shaft,unhook all wiring,it should pull right out.
How do you change the speed sensor on a 1999 ford escort se?
It is on top of the transmission you'll need to take the intake housing off to get to it. Disconnect the electrical connector. Take off the bolt holding a clamp against it's base and pull up.
How do you remove the fuel filter in a 2001 Mercedes E320?
take the cover off under the car its on the drivers side rear near the axle clamp both lines going into the tank
How do you check ampere draw?
Best way is to use a clamp on amp meter. You need to be able to put the clamp over a single conductor. This is usually easy to do in the electric panel, but for a device you need to split the conductors. You can take an extension cord you don't need and separate the conductors so you can get the clamp on a single conductor.
How do you fit a collar clamp on a scooter?
you have to take off your bars an take out the bolts on the clamp then slide it on the bars refit the bars straighten them up then tighten the clamp.
How do you take the axle out of a Chrysler 8.25?
To remove the axle shaft, first remove the wheel, and brake drum/rotor. Second, remove the differental cover. Third, remove the bolt holding the spider gear shaft, and remove that shaft. Fourth push inward on the axle shaft to remove the horseshoe clip on the inside. The axle shaft will now pull out.
What size socket do you need to take the axle nut off on 95 dodge neon?
22mm
How hard will it be to change out a CV axle on a 1989 escort gt?
Its really not that hard take the tire off, take the brake caliper off, take the bolt out off the ball joint (the spindal side) use a pry bar to push down on the control arm remove axle nut. Leave nut flush to end of axle use a hammer to free it from the hub.Once out, use pry bar on the inside off the axle and the trans and jerk it, there is a "C" retainer clip holding it in, also would recomend replacing the axle seal at the same time if its leaking.
Where is speed sensor located on 1995 ford escort?
It's on top of the transmission. You have to take the intake housing off to see it. It has the speedometer cable going into it and it has a bolt holding it in with a pinch clamp.
Can you get a clamp to clip a pittbulls ears?
if your talking about cropping no theres no clamp take it to the vet
How do you remove a ball joint on a 96 ford escort?
Jack it up and put it on stands. take off the wheel. Take of the clamp bolt and nut. Take the bolt completely out. Remove the 2 bolts holding the ball joint to the control arm. Take it off.
Replace rear axle on 2000 Dodge Dakota?
First off do you want to change an axle shaft or the complete axle housing? for the axle shaft,jack the rear of the truck up take off the wheels and brake drums.make sure truck is securly supported with jackstands.remove the differental cover locate the bolt that holds the cross pin in the carrier.remove the bolt,slide out the cross pin.push the axle in towards the center and remove the c-clip holding the axle in.remove the axle shaft carefully so not to damage the bearings or seal.
How do you remove the battery from a 2004 Monte Carlo?
You have to remove the black cross bar from above the battery and take out the plastic clamp holding the bottom of the battery before you can move it to where it will come out of the engine compartment.
