0
Answer for USA, Canada and countries running a 60 Hz supply service.
No. Even though 240 volts uses two breakers it is still classed as a single phase service. Kirchhoff's law states that current entering a circuit is equal to current leaving the circuit. Since the appliance draws 10 amps, the whole circuit has 10 amps flowing through it.
What else can I help you with?
If a 240v circuit hsa 30 amps per phase what is the amperage 30 or 60?
Still 30 amps, but at 240 V you'll have twice the watts that you would on a 120 V, 30 amp circuit, and after all, watts are what actually does the work.
What is the amperage of a 20 HP 240v single phase motor?
Typically single phase motors go up to 10hp. Wouldn't be very efficient at about 100 amps. A 20hp 3 phase motor at 230v pulls 52 amps. The 10hp single phase 230v pulls 50 amps.
How many output amps is a 600kva generator at 240v?
To calculate the output amps of a 600kVA generator at 240V, you would use the formula Amps = kVA / Volts. In this case, it would be 600kVA / 240V = 2500 amps.
How many amps in 17000 watts?
At 240v single phase it's 70.8 amps. If it runs on 2 wires plus ground, take the voltage rating of the equipment and divide that into the watts to get amps. At 480v 3 phase it's 25.8 amps. At 208v 3 phase it's 47.2 amps. <<>> There are zero amps in 14 kW. A voltage needs to be stated. I = W/E, Amps = Watts/Volts.
How many watts in 10amp's?
There is zero watts in 10 amps.
How many amps does a 240v well pump draw?
A 240V well pump typically draws around 10-15 amps.
What amperage will a range with a rating of 12.9 kw draw?
This depends on what voltage the range is rated for and if it is single phase or three phase. At 220 volts single phase it is about 60 amps, 240 v single phase , 53 amps and at 480 v three phase about 15 amps.
If an appliance draws 10 amps and the line voltage is 110 volts the power consumption is?
Power = volts times amps, so an appliance drawing 10 amps at a line voltage of 110 volts is consuming 1,100 watts. Keep in mind, however, that in a non purely resistive load, the phase angle of amps to volts might not be zero degrees, so the calculation becomes more complex, and depends on power factor, or phase angle.
1kw light bulb how many amps do you need if the voltage is 240v?
The basic formula for the Voltage, Current, Power relationship is P=I*E. To find one when the other two are known, simply fill in the two you know and solve. In this case P=1000W and Voltage = 240V (It is important that you pay attention to the unit definer here, if it were 240 mV, you would have Voltage = .240V and so on). 1000W = I * 240V I = 1000W/240V I = 4.17A
How many amps can a 1000watt inverter handle will it run a 10amp power saw?
A 1,000 watt inverter giving 110 volts is rated at 9 amps.
240 appliance 220 outlet will it work?
Yes, 220 and 240 volts are a nominal figure in the same voltage range. It is brought about by the power company, as they have a responsibility to keep voltages within a certain 10% range. The load will only notice a difference of 1% on the load current. e.g. Wattage load of 2400. Amps = watts/volts. 2400/240V = 10 amps. 2400/220V = 10.9 amps. On a constant resistance as the voltage goes lower, the current goes higher and vice versa as the voltage goes higher, the current goes lower.
How many amps will a 240 volt single phase 20KW generator supply?
Typically 75 amps on natural gas, 85 amps using propane. Peak amps(for less than a second) to start a big appliance, like an A/C condenser, are 130.
