0
What else can I help you with?
How do I properly store an rc servo?
Temperature is important in storage of a radio control servo. It is recommended to store the servo between 20C and 60C. pcbheaven.com/wikipages/How_RC_Servos_Works offers a wealth of information for those interested in rc servos.
What can I do with an rc servo?
An RC servo - a hobbyist remote control device - can be used for remote-controlled airplanes, robots or other devices that one wishes to operate from a distance.
What are the parts of a motorcycle?
RC motorcycle: Battery / fuel, servo, seat, brakes, etc
How do you make a RC boat?
You will need: a foam hull a propeller a tail rudder a servo a motor a receiver and a remote
Are there any 2001 dodge ram 1500 recall issues?
If you want to know if your truck has any recalls all you have to do is call the Dealer with your VIN number and they are required to check for you. Here are the possibilities for 2001 RC-B04-02 Safety Recall No. B04 - Power Distribution Center Cable Connections RC-982-01 Safety Recall No. 982 - Clockspring RC-966-01 Safety Recall No. 966 - Rear Axle Spring Seats RC-957-00 Safety Recall No. 957 -- Owner's Manual Addendum RC-955-00 Safety Recall No. 955 Upper Control Arm Fasteners RC-893-00 CALIFORNIA EMISSIONS RECALL #893 -- POWERTRAIN CONTROL MODULE RC-873-00 CALIFORNIA EMISSIONS RECALL #873 -- VECI LABEL REPLACEMENT
How do you make a 1-channel RC using a frequency crystal thingy?
You can buy a Transmitter and receiver on Ebay for a couple of bucks, there are plenty of old transmitters in the AM band that sell for pennies, boasting a total of 2 or 3 channels. You don't have to use them all! ;P They may sell the RC Radios and a receiver or even a TX-RX and Servo all in one package. The servo can be connected to any other mechanism to control drapes, windows, switches, or even door locks. All these suggestions run on either 4.5v, 6v, or 8v like most other RC (radio control) gear.
What can you use for an alternative of a servo in an RC plane?
Nothing. The servos are designed to react to a signal sent to the receiver from your remote and most will only connect to the receiver they were designed for.
How do you make a boat toy?
it is very simple ,you just need a RC car and a toy boatfit the motor at the back of the boat and for steering get a servo and take two cardboard pieces attach them to the servo moving part(shaft)like a real boat near the propelorr the propellor can be made from a can
2007 Chrysler sebring recalls?
These are the possible recalls I found. RC-H11-08 Customer Satisfaction Notification H11 - Radio Software Update RC-H07-08 Safety Recall H07 - Tire Pressure Monitoring System Electrical Connectors RC-G12-07 SUPERSEDED BY :RC-G33-07(Safety Recall G33 - Front Door Latch Cables) RC-G33-07 Safety Recall G33 - Front Door Latch Cables RC-G23-07 Emissions Recall G23 - Reprogram TIPM: Transmission Default RC-G14-07 Safety Recall G14 - Seat Track Position Sensor RC-F50-07 Revised Safety Recall F50 - Reprogram ABS Control Module RC-F51-06 Safety Recall F51 - Reprogram HVAC Module RC-F45-06 Safety Recall F45 - Hood Latch Striker
How do remotes control toy cars?
Most RC cars operate under a 2-channel radio system(steering and acceleration). The remote transmits a series of signals to two different servos on the car, the accelerator servo and the steering servo. these signals tell the car what to do
Does RC have pork?
Yes, RC (Royal Crown) Cola does not contain pork or any pork-derived ingredients. It is a carbonated soft drink made primarily from water, sweeteners, and flavoring agents. However, if you have specific dietary concerns or restrictions, it's always a good idea to check the ingredient label for any potential allergens.
Could you use a acoms ic as-7 servo with a 20t motor?
Yes, you can use an ACOMS IC AS-7 servo with a 20T motor, but you need to ensure that the servo's specifications are compatible with the motor's requirements. The AS-7 is typically designed for steering applications in RC cars, while the motor's 20T designation refers to its turn count, affecting its torque and speed characteristics. Ensure that your power source and control system can handle the combined load, and consider the application to ensure optimal performance.
