0
Does code require a new bath vent fan to be on a dedicated circuit?
Wiki User
∙ 12y ago
No, the bath vent fan does not need a designated circuit. If this is a new installation install a three wire cable to the fixture from a two gang switch box. Cover plates for two gang boxes can be bought with a blank on one side and a switch on the other. At some time in the future a lighted fan enclosure may be installed. This will allow the light and fans to be operated independently.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
Can a dedicated circuit share a neutral?
It depends on:what you are calling a dedicated circuitWhether there is ANY possibility that the neutral could be required to carry a load in excess of the rating of the wire.First we have to make certain that we're talking the same language, second we have to consider the fire hazard involved. (although, if we're looking at safety, we would need to reverse the two)The simple answer is No.The term "dedicated circuit" is not defined in the code. But in practice the term refers to a circuit that is run for a particular purpose, often to one piece of equipment or receptacle (outlet). Sharing a neutral contradicts the principle of a dedicated circuit.Sharing a neutral would expose the circuit to electrical elements such as harmonics. A dedicated circuit is intended to avoid such problems.
Does a dishwasher need a dedicated circuit?
Dishwashers do not have to be on a dedicated circuit, according to NEC codes. Neither do refrigerators. Electric Ranges and OTR Microwave Hoods and Hood Fans do. First, always ascertain the appliances that will be in the room and regularly used, and calculate their wattage or look it up in the specs found on the appliance or in its manual. The dishwasher issue is a falsehood espoused by many kitchen designers, home inspectors and electricians who have apparently substituted their own opinions as being code. I just read all of the applicable NEC codes. They are readily available for purchase or for free at your local library. Consulting it yourself is the best bet. It does not specify a dedicated circuit for the dishwasher. It can be on a branch circuit for the kitchen, but if it's sharing the circuit with other appliances, then it must not use more than 50% of a branch circuit's load capacity. So that in effect creates a dedicated circuit requirement IF your circuit is a 15 amp circuit. If it's a 20 amp, you may have capacity room for a small load appliance such as the disposal or refrigerator, depending on load calculations (Volts x Amps = Watts (Load). But if you use a 30 amp or higher circuit capacity, then you can comply with code much easier if other small appliances are on it. NEC 210.23
When does code require junction box covers to be labeled?
Junction box labeling is required by Code (NEC) on boxes containing fire alarm circuits and circuits fed from emergency power panels backed up by generators. However, it is a good trade practice to always label your j-box covers with the circuit voltage and circuit numbers.
Can you use a 240 volt 40 amp GFCI circuit breaker for a stove?
Yes you can but the electrical code does not require it. To use one where it is not requested to do so is just adding to the over all expense of the project.
Does 2005 nec code require tamper resistant outlets?
No, but the code as of today (2012) does require tamper proof outlets.
Does a freezer absolutely need a dedicated outlet?
Current code say that a freezer or any appliance needs to be on it's own circuit. It will still work if it is not on a dedicated circuit.
Does a fire alarm control panel need a dedicated branch circuit?
Under the NFPA Fire Alarm Code, the control panel must have its own dedicated circuit, the circuit must be labeled "Fire Alarm Circuit" and the handle of the circuit breaker must be colored red. Other rules apply in jurisdictions that adopt other standards, or for other types of fire alarms. For example, under New Hampshire Fire Code, you are PROHIBITED from installing self-contained smoke alarms on a dedicated circuit.
What is a dedicated outlet?
A dedicated outlet is a single circuit from a single or double pole breaker to a specific outlet or receptacle for a single specific device or appliance. An example of this would be a circuit for a refrigerator, microwave, dryer, range, etc..This is typically referred to as a "dedicated circuit". A dedicated circuit usually is supplying power to only one or perhaps two receptacles, such as a computer station. An example in your home under current code is your washing machine is required to be on a dedicated circuit. Dedicated receptacle circuits may be either 15 or 20 amp.A dedicated circuit is just what it sounds like. I'ts a circuit dedicated to one particular device. Most receptacle (you may call them outlet's) circuits will power several outlets. A dedicated circuit will power only one specific outlet or appliance. Some examples would be a refrigerator, a garbage disposal, or a microwave.
Are there new regulations on wiring dishwashers?
Not in the latest edition of the code book. It should be on a 15 amp dedicated circuit.
Does a microwave need a 15 or 20 amp circuit?
By code you're supposed to have a dedicated 20 amp circuit. But if you have an existing 15 amp circuit it might be fine for now if your microwave is 1400 watts or less and there's nothing else drawing power from that circuit. But if your running it new definitely run a 20 amp circuit dedicated on 12 gauge wire. That will allow you to use any microwave you want now and in the future.
Can a dedicated circuit share a neutral?
It depends on:what you are calling a dedicated circuitWhether there is ANY possibility that the neutral could be required to carry a load in excess of the rating of the wire.First we have to make certain that we're talking the same language, second we have to consider the fire hazard involved. (although, if we're looking at safety, we would need to reverse the two)The simple answer is No.The term "dedicated circuit" is not defined in the code. But in practice the term refers to a circuit that is run for a particular purpose, often to one piece of equipment or receptacle (outlet). Sharing a neutral contradicts the principle of a dedicated circuit.Sharing a neutral would expose the circuit to electrical elements such as harmonics. A dedicated circuit is intended to avoid such problems.
What is the zip code for Bath Pennsylvania?
The ZIP code for Bath, Pennsylvania is 18014.
How many Amperage for a gas stove?
A gas stove needs no high current. A basic 15amp circuit will suffice. Code will probably require a 20amp circuit since its in the kitchen.
What is the country code and area code of Bath United Kingdom?
The country code and area code of Bath, United Kingdom is 44, (0)1225.
What size breaker should be used for a fridge?
read the manufactures data plate on the back of the fridge it will tell you the amps and voltage of the fridge. But most likely will be a 20 amp circuit. code requires min size out lets for stand alone appliances in kitchen to be 20 amp.
Can the surge from a refrigerator cycling on and off damage the circuitry of a gas furnace aqua stat or other electronic equipment?
Yes it can, but I will only give you clue as to why. "What does a single phase motor need to start the motor?" Extra credit!!! Does The Code require a dedicated circuit for the refrigerator? ( I might be a worse teacher than the one you have! )....pkazsr
Can you wire lighting fictures to receptical circuits?
Yes as long as you stay within your local code. Usually a combination of lights and receptacles cannot exceed ten total. Do not wire any light to a circuit that requires a dedicated circuit, such as a refrigerator, dishwasher, etc.
