The fuse is there to disconnect the supply when there is a short circuit, before any damage is done.
Chances are there is more than 1 outlet connected to the 110volt circuit you are looking to convert. So therefore the easy answer is No. The 240volt dryer circuit must be a dedicated single circuit for the dryer only.
No you can only have one dryer on a 240v circuit and nothing else can be attached to it either considering your using a 240v electric dryer
It should be in the main circuit panel. If the dryer was added at some point there may be a separate box just for the dryer either beside the main panel or at the dryer plug. It is not in the dryer itself.
depends on the wattage of the hair dryer. most are 1250 to 1600 watts so a 20 amp gfci circuit would be able to carry the load of a standard hair dryer.
The short answer is no. First off I assume you mean "can you have a dryer and an electric range on the same circuit?" (If they were actually wired in series, then you couldn't use your range if the dryer was off) In theory you could have them on the same circuit you just need to make sure that the wiring and the circuit they are on can handle the number of amps the two of them could draw together. If your breaker isn't big enough, it kill the power to the range while you are cooking dinner. If the wiring can't handle the load, then there is a fire risk. A dryer is usually on a 30amp circuit and a range is usually on a 50amp circuit, so to have them together would require an 80amp circuit, which will be difficult to find a breaker and wiring for.
Typical residential electric dryers are on 30 amp circuits, which means 10 gage copper wire. The circuit breaker should match the dryer cord rating, generally 30 amps.
No. An electric dryer has no burner or combustion controls.
== == A dryer outlet is only safe to use for one purpose: to power a dryer.Obviously you can attempt to use it for something else, such as an electric range, but it is NOT SAFE to do it!You could drive on the wrong side of the road but it is NOT SAFE to do it!You could put your hand into a fire but it is NOT SAFE to do it!In general the reasons for saying it is not safe to use something other than a dryer on a dryer outlet are all about being sure that the circuit you will use for the other appliance (in this case an electric range) has: * the right size of wires to carry the current the appliance takes and* the right size of breakers on the main supply panel to protect the appliance - and the wiring to it - from catching fire if there is ever a malfunction. Electric ranges are quite different to dryers: people are likely to be "in close attendance" to them all the time they are on! You have to be sure you wire them up correctly and safely to avoid there being any kind of risk of anyone getting electrocuted.You also have to be sure that the supply circuit used is of the right kind to protect the house from a house fire. That can happen if there is a malfunction in the range but the circuit breakers on the main supply panel - or the wiring feeding it - are the wrong size. The circuit breakers on the main supply panel - and the wiring feeding the outlet for the range - must all be properly sized and correctly and safely installed. == == For more information please see the Related Questions shown below. As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
Hair dryer. I had the same question,weird.
I beleve mine blew do to a lose power connectionn at the circuit board. These are the press on connections.
If a dryer is really not good to begin with, nothing you can do can stop it from getting damaged. But one way to prevent the dryer fuse from blowing is by ensuring that it is hooked to the right connection. Make sure the voltage is right. Avoid overloading the electricity socket. Clean the lint screen as well. If lint gets in the way of proper air exhaustion inside the dryer, it might overheat.
There is no requirement on the distance the dryer must be from a sink. Any 120 volt outlet must be GFCI protected if it is within 6 feet of a sink. There is no requirement for a 240 volt dryer outlet. I would not want the dryer right next to the sink and I would want the dryer to be on a 4 wire circuit and not a 3 wire circuit. Use common sense here.