0
Does increasing the amp hours of a 36 volt battery system have the potiential to overload a motor?
Wiki User
∙ 14y ago
No. Amp-hours is the measure of how long the battery can keep doing the job before it's exhausted. As long as the voltage of the battery remains the same, the motor doesn't know that anything has changed.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What is used for overload protection in a hydraulic system?
A relief valve is installed in the system, often in the pump itself, to relieve (not prevent) any overpressurization of the system.
Does battery room reqire air colling system?
A battery room may not require cooling, but it will require low humidity -- and for that you may need a cooling system or air conditioner.
Temporary drop in AC power?
There are lots of causes - a short in your home (breaker went, or fuse went to clear the fault), temporary overload (something using lots of power turned on), a short on the electric system outside your home (breakers or fuses may have operated), overload on the system, sudden loss of generation capacity, icing, faulty equipment (perhaps an LTC went haywire), etc.
Can you use three phase thermal overload relay in a single phase system?
Yes, when using a three phase contactor on single phase, the three phase overload block can be used. The wiring of the contactor consists of taking L1 of the supply and connecting it to L1 of the contactor. The load is connected to T1 on the bottom of the overload block. L2 of the supply is taken to L2 of the contactor. Instead of connecting the T2 to the load, the conductor is taken back to the top and connected to the contactor in position L3. The other side of the load is connected to T3 on the bottom of the overload block. The overload block has three N.C. contacts, one for each leg of L1, L2 and L3. These three contacts are wires in series to the stop - start circuit. Years ago on old schematic diagrams these contacts used to be placed on the up stream side of the magnetic starter's coil. When the overloads tripped the voltage was left on the control circuit which was found to be dangerous for trouble shooting. Now the overload contacts are positions on the beginning of the start- stop circuit so that when a overload trips, the whole stop - start circuit becomes de energized.
Will system boot up normally to operating system level if CMOS battery is dead?
CMOS holds many of the boot parameters, such as what type and size of hard disk, the type and speed of the processor and other critical information. Many times the computer can still boot with a dead CMOS battery, but the information will not be available and will affect the process. Replace the battery then run through the setup procedure to save the values.
When was System Overload created?
System Overload was created in 2006.
Is the sum of potiential and kinetic energy in a system called total energy?
sure
Which of these can hellp you avoid information overload?
There are various things that can help you avoid information overload. The most important thing is to ensure that you have a proper management system for information.
Why do the fuses keep going out in your 93 Honda civic?
Overload or short in system
What happens when you create overload on a body system?
muscles react,which means they increase in size
What happened to the nervous system causing you to faint?
To put it plainly there is a system overload of sorts, and the body essentially stalls momentarily.
What is the cause of burned out fuse box in a 1984 buick regal It looks as if the fuse got too hot.?
Bad wireing, bad grounding, incorrect battery, or system overload as in using your stereo and lighter at the same time also (audio systems)
What is used for overload protection in a hydraulic system?
A relief valve is installed in the system, often in the pump itself, to relieve (not prevent) any overpressurization of the system.
If a 100a breaker keeps tripping?
If a 100 amp breaker keeps tripping there is an overload on the system.
Local battery telephone system vs central battery telephone system?
In local battery telephone system, the subscriber has to own a local battery with hand generator, so that he will give ring to central office ( to operator ) to call connectivity.In central battery system, the telephone exchange feeds the battery to customer premises equipment ( instrument )
What is Slope overload distortion?
Slope overload distorsion - is caused by use of step size delta which is too small to follow portions of waveform that has a steep slope. Can be reduced by increasing the step size. Granular noise - is caused by too large step size in signal parts with small slope. It can be reduced by decreasing the step size.
What is the function of fuse in automotive application?
Same as any fuse in an electrical system- to protect components in the electrical system from damage in an overload or short circuit.
