0
Does the cable frame on pottery barn teen actually have cables?
Wiki User
∙ 12y ago
I don't know. What kind of a question is that.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
How do you know which battery cable is positive and which is negative in a car if they're not labelled and not connected to a battery?
Following the cables into the engine compartment. The positive cable will run to the alternator or the starter. The negative cable will just connect to a ground source (engine block, frame, etc.)
Got these clear sticker with new bike what are they for?
They go on the frame, to protect it against cable rub. Put them anywhere a brake cable makes contact with the paintwork. Mainly up by the headtube where the cables from the bar curves down.
How do you adjust parking brake travel on a 2000 Dodge Grand Caravan the dealership is trying to sell a 350 dollar ratchet but the ratchet works fine suspect stretched cables can cables be adjusted?
Yes, cable can be adjusted . Somewhere in the main brake cable there is a square frame adjuster you change with 2 wrenches.
One of my battery cables has a second smaller gauge wire running from it to the drivers side firewall. I removed the old battery and now need to know which is the pos and which is the neg cable?
the negatibe cable will be black. the positive cable will be red the negative cable will bolt to the vehicle frame or body the positive cable will bolt to a solenoid or starter motor also usually the cables will only fit one battery terminal. battery terminals are different sizes
How do you hook cables to battery?
you hook the positive cable,(usually the red) to the positive battery terminal first then you hook the negative cable(usually black) to the negative terminal if you hook it the other way you can get sparks or arcing that can cause damage or a fire PS: if both cables are same color, the negative cable is the one bolted to the frame or the engine.the poitive is bolted to the solenoid or starter
How do you adjust cables in brake drum?
You don't normally adjust in the brake drum. There is usually an adjuster about halfway to the back, under the driver side. This is an oblong metal frame where the front cable joins the cable to the rear splitter. You tighten a nut in this box to adjust length of cable.
Is the white battery cable on a camper trailer positive?
White is typically the Negative or ground side of the system. If in doubt it is best to trace the battery cables to see where they go. The ground will always be attached to the frame of the camper some where close to the battery. Make sure the cable is attached to the frame and not an insulated stud attached to the frame. Insulated studs will have a rubber or plastic boot on the stud.
Where are the ground wires located in a 92 Honda Prelude?
follow the negative battery cable to the frame that is usually the main ground but there are many body tied ground cables throughout the car
What will happen if you replace an alternator without disconnecting the battery cables?
If you are careful and do not let the positive cable to the alternator come in contact with the motor or frame, nothing will happen. It is just a lot easier and safer to disconnect the positive cable from the battery. It saves possibly shorting out the cable and possible ruining the battery.
Where could one find a pottery barn frame?
The best place to find pottery barn frames is the official pottery barn homepage. There one can find a lot of nice looking different pottery barn frames.
Why are the brake lights on your 2001 Mercury Villager are always burning out?
First, make sure you are using the correct bulb (3157). Next, believe it or not , you may be experiencing a low voltage situation. Have the battery tested and take a close look at the battery cables. Corrossion that developes at the terminals can invade the rest of the cable and cause low voltage/amperage problems. Replacing the cables will cost about $50 apiece. Obtain them from a dealer. Universal cables will not work. The positive cable has a special connector on it. The negative cable is a one piece assembly with connectors for the frame and to the engine.
Is a load supported on three members statistically indeterminate?
No, it is not statistically indeterminate. Well, sometimes it is, sometimes it isn't. It depends on how you frame the problem. Consider a cube hanging from three cables to the ceiling. If one cable is over the center of gravity and two cables are at opposite corners, the load in each cable is indeterminate. But imagine the cables connected to three corners. If the cube is hanging level it is clear that two opposite corner cables each carry half the weight, and the third carriers zero. The problem is determinate. If we crank up on the third cable and the cube is not level, the problem becomes slightly more complicated. But by taking moments about each anchor point and considering the tilt of the cube, the load in each cable can be found. The problem is determinate.
