No
A resistor will not change its value, unless the voltage exceeds the designed power capacity of the resistor. As the voltage increases, the current will increase, if the current gets too high it will cause the temperature of the resistor to increase, if the temperature exceeds the power rating of the resistor then the resistance WILL change. If it goes too High in temperature the resistor will open and current will no longer flow. A resistor is used to control current, and indirectly the .voltage depending on the application. Hope This helps. You must use Ohms Law to see the relationship.
A: If you know the total resistance and total voltage then you know total current flow for the circuit, this current will be same for every resistor in series however the voltage drop will change for each resistor . So measuring the voltage drop across the resistor in question and divide by the total current will give you the resistor value.
When a dc supply is connected to a resistor, current flows. The current in amps is equal to the supply voltage divided by the resistance in ohms. The power used is the voltage times the current, and that appears as heat in the resistor, which might become hot to touch.
It decreases by a factor of 4
A: A TRANSISTOR gain is determined by current flow on the collector by adding a resistor to the emitter this current flow is reduced by adding or bypassing this resistor with a capacitor the net effect is that this emitter resistor will be reduced in value as frequency increases therefore change gain as a function of frequency input
Variable resistor is an resistor that can change its resistance manually, by rotating a handle or a screw.
A resistor resists the flow of current in a circuit but a transistor changes the amount of current through a device. This is called current magnification. Field effect transistors FETs and MOSFETs (metal oxide semiconductor field effect transistor) may also change the amount of current to a load lastly a variable resistor or a potentiometer or a variable resistor can variate the amount of current at your will
The voltage must reduce by the same factor - that is Ohm's law.
The potential difference accross the resistor changes mainly due to gradual increase accumulation of electrons in the lower potential region which will in turn affect the potential gradient as the current flows through the resistor
A resistor will not change its value, unless the voltage exceeds the designed power capacity of the resistor. As the voltage increases, the current will increase, if the current gets too high it will cause the temperature of the resistor to increase, if the temperature exceeds the power rating of the resistor then the resistance WILL change. If it goes too High in temperature the resistor will open and current will no longer flow. A resistor is used to control current, and indirectly the .voltage depending on the application. Hope This helps. You must use Ohms Law to see the relationship.
A: If you know the total resistance and total voltage then you know total current flow for the circuit, this current will be same for every resistor in series however the voltage drop will change for each resistor . So measuring the voltage drop across the resistor in question and divide by the total current will give you the resistor value.
A varistor is a variable resistor. It changes value dependent on the current draw and operates by changing its value as the resistor's temperature changes. For instance, during turn-on of a device, the resistor heats up causing the resistor to change it's value, thereby limiting the inrush current to the device. Once the initial start-up current is reduced and the device is operating normally, the resistor cools down and changes value again.
Generally, yes. It would depend on the device you are talking about. In a resistor a change in current will result in an instant change in voltage. Inductors and capacitors do not change instantaneously but will over time.
A resistor in a sensor circuit is used as a simple way to monitor the function of the circuit. The resistor has a calibrated and known voltage drop and current while the circuit is "normal". If there is a short-circuit, or an open-circuit, the voltage and current will change and trigger the trouble alarm.
If forces on an object are unbalanced, it will accelerate (its velocity will change). If torques are unbalanced, it will start to rotate - or more precisely, its speed of rotation will change.
A variable resistor is used in cicuits to vary the current passing through the resistor. It is commonly used to change the value of current across a circuit, or to act as a voltage divider. They are commonly equiped with a knob outside of a cabinet, to enable the user to adjust the operation of a circuit, like a volume control on a radio or amplifier.
unbalanced foeces