Fuel and Fuel Intake
Chevy Suburban
Vauxhall
Ford Ranger XLT

Does the engine in a 1996 vectra 18 ls ecotec have fuel injection?

262728

Top Answer
User Avatar
Wiki User
2005-12-19 18:01:21
2005-12-19 18:01:21

yes.......PS

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

A 1996 Punto 55 uses a single point (non-direct) fuel injection system. Later models adopted a multi-point injection system but none of the Fiat 1.1 engines use direct injection.

User Avatar

( Yes ) the 2.3 liter four cylinder engine in a 1996 Ford Ranger is fuel injected

User Avatar

Both the lift (transfer) and injection pumps are on the left side of the engine.Both the lift (transfer) and injection pumps are on the left side of the engine.

User Avatar

6.2L idi (indirect injection) not the best diesel trucks..

User Avatar

hi its just behind the oildipstick and just under engine cover hope this helps

User Avatar

vortec trucks have MPI Multipoint fuel injection. yes it's not getting enough electic to the wires to fuel pump

User Avatar

Yes. Sequential-Port Injection.

User Avatar

Gas engine, the fuel pump is in the fuel tank. Diesel engine, the lift and injection pumps are on the engine block.

User Avatar

Fuel injection engines DO NOT HAVE A CHOKE. Is your check engine light on ? You need to have the engine scanned with a scanner to see what is going on.

User Avatar

I have a 1997 1.6 vectra and I got up to 200 km, but I didn't push it to its limits!

User Avatar

Nope. The engine block would not bolt up to the 1996 trans, as the bolt pattern was changed when they updated the transmission design. Also, since the 89 engine uses throttle body fuel injection, and the 96 uses multi-port fuel injection, the wiring harnesses would not be compatible.

User Avatar

try in front of the back wheel at the drivers side. just where the fuel lines leave the tank and head for the engine..

User Avatar

If it is the VORTEC engine then it is bolted to the passenger side of the timing cover on the front bottom side of the engine. If it is the TBI / THROTTLE BODY INJECTION engine then it don't have 1.

User Avatar

The first year of fuel injection on the Road King was 1996.

User Avatar

To put a 1996 7.3 powerstroke engine into a idi diesel truck you would have to transfer the ecm and the entire engine wiring harness over the old truck, the 1992 is a non-electronically controlled engine and the 1996 cannot run without a computer because it has high pressure electronic unit injection. This swap is possible, but very difficult.

User Avatar

The IAT sensor is mounted in the backside of the air cleaner housing for a 1.6 MFI (Multipoint fuel-injection) engine and for a TFI (Throttle body fuel-injection) enging it's located on the right hand side of the engine, mounted in the intake manifold below the throttle body.

User Avatar

The indicator flasher unit in your 1996 automobile is located beneath the dashboard. The unit simply plugs in and out.

User Avatar

Assuming we are talking about a 4.3L engine, the 96 would be CFI (Central Fuel Injection) and the 95 would be TBI (Throttle Body Injection). The engine would bolt in but all the electronics including the fuel pump and fuel lines would also have to be swapped, or swap the 95 throttle body unit over to the 96 engine.

User Avatar

Yes, it can be done but it will be very expensive. The engine, computer, transmission will need to be properly fitted. Custom mounts and axles will have to be produced. The wire harness will need to be upgraded as well to handle the new computer.

User Avatar

The capacity of a 1996 engine is about 14 gallons

User Avatar

No it will not. 1994 and 1995 only will from car or truck. 1996 went to a different computer system, fuel injection, camshaft, cam sensor, etc.

User Avatar

The 88 engine is a TBI / Throttle Body injection engine. I don't know the month of 1996 when they changed to the vortec engine fuel system, But I believe it was in late 1996. You should know if the 1996 engine is a TBI engine or a vortec engine if you have Sean it. So if it is a TBI engine then you have no problems, Put it in there and hook everything up and your good to go. Now if it's a vortec engine you have problems, None of the wireing will hook up to the 88 engine sensors. And the 96 computer will not run the 88 engine. And the fuel pump in the 96 Tahoe has to much fuel pressure for a TBI engine. You can not put the vortec fuel system/ intake manifold on the 88 engine because none of the intake bolts will match the heads or vise verse. You will be opening a can of worms. You need to go back with a vortec engine if that is whats in the Tahoe now.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.