0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
Rear window defroster?
what are the colors of the wires for the rear window defroster coming from the rear window to the defroster bottom ? can any body help me
Rear power window works only when rear dooris open on 2004 Cadillac Deville?
I'm having the same issue. Any help, guys?
Do any window shades keep UVB out?
The Roll-On Window Shade for cars do.
Where are the fuse boxes in an alero?
At each end of the dash when you open the doors. There is a panel on both sides that open and the fuses are in there, although I could not locate the fuse for the rear window defroster. Any help out there?
Can you interchange the rear window regulator with the front on a ford contour?
That would be EXTREMELY unlikely that any rear window regulator would fit in the front window, same side or not.
Where can I buy window decals?
on signazon you can buy cheap window decals. for any purpose whether it is for cars or just for any window they can also be customized for any company or purpose.
Can you drive with the rear window open on an 2004 Tahoe?
If you can or not is really not the question you should be asking. The real question is "Should" you? It is unsafe to drive with the rear window open on any car. This allows exhaust fumes to possibly enter the vehicle, thus causing a hazard to your health. Carbon monoxide is a killer and you may end up dead. Do not do it, even if it is possible.
What cars are not easy to break in?
Any car can easily be broken into as all cars have windows. Break the window and you are in.
How do you initialize the rear window motor on a 2001 ford sport trac?
Rear Window Motor InitializationWhen you install the new motor, it MUST BE "INITIALIZED" before it will function properly. Simply follow the instructions below. CAUTION: Make sure that no obstructions are present in the power rear window system when carrying out this procedure.NOTE: The rear window motor is in error mode when shipped and will be inoperative until initialized.NOTE: This procedure must be carried out when repairs are performed on any part of the power rear window system including when: the power rear window motor is removed from the window regulator drum housing, a new power rear motor is installed, a new power rear window regulator is installed, a new power rear window glass module is installed, and any operation in which grease or lubricants are applied to the power rear window system.NOTE: All power rear window components (window glass module, window regulator, window motor, and glass runs) must be installed and torqued to specification before carrying out this procedure.NOTE: Once the ignition key is turned to the ON position in Step 6, it must remain on until the entire procedure is completed.NOTE: Step 7 requires that the power rear window control switch be held in the CLOSE position (fully clockwise) until the power rear window motor stalls the window into the upper header seal. Step 8 requires that the window control switch be momentarily turned to the OPEN position.NOTE: Step 9 requires that the power rear window control switch be held in the CLOSE position (fully clockwise) until the window stalls into the upper header seal and the window carries out its down-up sequence, indicating successful completion of initialization.NOTE: The key-in-ignition chime can cause the vent button to be pressed more or less than six times due to the distraction of the chime.NOTE: Steps 1-6 must be completed within 30 seconds. The entire procedure must be completed within five minutes.Start with the ignition in the OFF position. Open the driver door.Turn the ignition to the ON position.Press the power rear window control switch vent button six times.Turn the ignition to the OFF position. The driver door must be OPEN.Press the power rear window control switch vent button six times.Turn the ignition to the ON position. The power rear window will move down-up-down-up approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has entered initialization mode.Rotate and hold the power rear window control switch to the CLOSE position until the window stalls into the upper header seal.Momentarily rotate the power rear window control switch to the OPEN position and release. The power rear window will carry out a one-touch down operation until the window stalls at the bottom of the travel stop designed into the window regulator.Rotate and hold the power rear window control switch to the CLOSE position. Continue to hold the switch until after the window stalls into the upper header seal and carries out the down-up movement. This down-up movement is approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has been successfully initialized.Verify correct operation of the power rear window by moving the window to the fully open, vent, then fully closed positions. If the window does not operate correctly, carefully repeat this procedure.NOTE. You will need to close the door after step 6.
What should you do if Photo Booth says it's open but doesn't open any window?
The window may be minimised into the dock. Clicking the PhotoBooth icon in the dock will reveal any windows that it has open.
How do you know if a power window is heated?
The only window that is heated in any car is the rear window. As far as I know ther's no such thing as a power heated window
What is reasenDouble click on any drive then drive open in new window?
You have probably configured Windows to open drives and folders in a new window.
